Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Waveband WVX-TWC1-MT16
Summary of Contents for Waveband WVX-TWC1-MT16
- Page 1 Single Unit Rapid Charger USER MANUAL...
-
Page 2: Table Of Contents
Waveband Single Unit Charger Table of Contents Topic Page Introduction Important (read before use) Caution (read before use) Replacing A Charging Pod Charger Features Charging A Battery Fault Conditions & Advisements Warranty And Service Specifications Accessories... -
Page 3: Introduction
(Li-Ion), lithium polymer (LiPo), nickel-metal hydride (NiMH), or nickel cadmium (NiCd). If you wish to replace the charging pod in the future, check with Waveband customer service to ensure the replacement pod selected is compatible with your model. For a complete list of charging pods available, call toll free... -
Page 4: Important
Important Read all Caution statements below and this User Manual before attempting to charge a battery. Check to make sure a charging pod compatible with your battery is properly installed before charging a battery or installing the charger in a vehicle. Always charge new batteries completely before initial use. -
Page 5: Caution
Do not attempt to charge a battery without first installing the appropriate charging pod. Use only charging pods designed for this Waveband charger. Disconnect charger from the power source before installing, adjusting, or removing the charging pod. -
Page 6: Replacing A Charging Pod
Caution (continued) Make sure contacts in charging pod and on the battery are clean. Do not allow wire or metal objects to touch contacts in charging pod or any internal part of the charger. Do not remove the charger’s housing or make any modification to the charger. - Page 7 Replacing A Charging Pod (continued) Follow these steps to change the charging pod: Obtain a charging pod made specifically for this Waveband charger. Confirm that the charging pod is compatible with the battery you want to charge. Unplug the charger from its power source.
-
Page 8: Charger Features
Charger Features Status LED information – also see bottom label. Charger base. Charge status LED – illuminates Removable charging pod. green, red, or orange. DC power connection – AC to DC power supply back of charger. -
Page 9: Charging A Battery
Charging A Battery Confirm that the charging pod and battery are compatible. Connect the charger to power with the power supply included. Place the battery to be charged in the charging pod. The battery may also be charged while attached to the radio. When a battery is placed in the charging pod and while charging, the status LED will illuminate RED with no flashing to indicate normal charging. - Page 10 Charging A Battery (continued) The charge status LED will illuminate GREEN with no flashing when the battery is fully charged. After removing a fully charged battery, the charge status LED will illuminate ORANGE for a few seconds. Allow the charge status LED to go off before placing another battery in the charging pod.
-
Page 11: Fault Conditions & Advisements
Fault Conditions & Advisements When the charge status LED flashes RED, a fault condition exists. A fault condition requires immediate attention. When the status LED is solid or flashes ORANGE, you are receiving an advisement about the battery. The flash patterns for fault conditions are as follows: LED Pattern Fault Description Flashes RED... - Page 12 Fault Conditions & Advisements (continued) LED Pattern Fault Description Flashes RED Battery temperature is 45°C (113° F) or above. Charging has terminated, remove battery from charger. Have battery checked by a qualified 3 Times technician. The flash patterns for advisements are as follows: LED Pattern Advisement Solid ORANGE...
- Page 13 Fault Conditions & Advisements (continued) LED Pattern Advisement Solid ORANGE Indicates (A) battery is too cold or (B) charger is performing a temperature diagnostic when the battery is inserted. If (A), the battery (Battery inserted.) temperature is 0°C (32° F) or below and charging is delayed for up to two hours.
-
Page 14: Warranty And Service
This is the only warranty made by Waveband. In no event will Waveband, its affiliates, subsidiaries, related entities, or their respective directors, officers, or employees, be liable for any damages beyond repair or replacement as described above, including without limitation, indirect, incidental, or consequential damages. -
Page 15: Specifications
Specifications Dimensions (W x L x H) 96 x 131 x 77 mm / 3.8 x 5.2 x 3.0 inches Weight 0.25 kg / 0.55 lbs. (charger only) Compatible Chemistries Li-Ion / LiPo / NiMH / NiCd (based on pod selected) Ambient Operating Temperature 5°... -
Page 16: Accessories
Accessories Information Part Number Description Power supply. UL listed. Input: 100-240V, 50-60Hz, PS-SSDCH (Included with charger.) 0.5A. Output: 15.0V, 1.0A. Vehicle power adapter. Length: 20.0” (cord relaxed). PS-SSCC (For in-vehicle use.) Replaceable fuse, 2A. Heavy duty vehicle power adapter. Length: 24.0” (cord relaxed). PA-SSCC (For in-vehicle use.) Replaceable fuse, 6A. - Page 17 1912 Liberty Road Road • Unit 14 • Eldersburg, MD 21784 www.wvbandcoms.com...