Related Manuals for RCA RBA29550
Summary of Contents for RCA RBA29550
- Page 1 RBA29550, RCA29520, RCA33683, RCA37683 USER’S GUIDE It is important to read this manual before operating this unit for the first time. TOCOM 15128920 L O R...
-
Page 2: Important Information
If you need and exten- sion cord, make sure it matches the plug of the TV. For Models RBA29550, RCA29520, RCA33683, and RCA37683: Operate TV on 90-260 volts, 60 HzAC power (normal house power). -
Page 3: Table Of Contents
References Warning, Product Registration Startup ____________________________________________________________________ Hook up your TV, Plug in the TV, Put Batteries in the Remote, Turn on the TV, Place Channels in Memory, Set the Time Basic Tour of the Remote ____________________________________________ Power, Volume, Channel, Components buttons... -
Page 4: Quick Guide To Your Tv
CAUTION: If you choose not to use the stand recommended for your TV, take precautions that the stand or furniture the TV is placed on is properly located and of adequate size and strength to prevent the TV from accidentally being tipped over or pulled off. This could cause damage to the TV and or personal injury. - Page 5 Earth's magnetic field on a large picture tube. The PICTURE TILT STRENGTH and POLARITY switches on the back of the TV compensate for this effect. If the picture appears tilted, follow these steps to improve it.
-
Page 6: Basic Tour Of The Remote
Details are on page 6. Component Buttons Details are on pages 8–15. Menu Buttons See next page for details. Turns the TV on. Sets the remote to control the TV. PLAY STOP PAUSE DISPLAY SKIP Operates TV when remote is set to control the TV. -
Page 7: Menu Basics
The menu buttons are used to adjust the features in the TV’s menus. Both the menu buttons on the remote or the front of the TV will move through the menus. See “Moving through the Menus” below. Moving through the Menus... -
Page 8: Using Your Remote
Player and Audio equipment on pages 8–15. Turns on the TV. Shows the displays on the screen. Sets the remote to control the TV. See Using the Remote with a VCR, Satellite Receiver, Cable Box, Laserdisc Player and Audio equipment on pages 8–15. - Page 9 Using Your TV and Remote With Remote Buttons PLAY STOP PAUSE DISPLAY SKIP MUTE PREV CH INPUT ANTENNA • CLEAR RESET MOVE Number Buttons (0-9) Selects any channel number. Two numbers must be pressed for each channel. Press 0 and 6 for channel 6.
-
Page 10: With Vcrs
Philco ...08,29,35,56 Philips...08,29 Pioneer ...05,16,33 Portland...44,45,52 ProScan...00 Quartz...02 Quasar ...08,53 RCA ...00,05,07,08,28,35,37,54,69 Radio Shack ...02,06,08,09,12,15,19 Press VCR1 or VCR2•LD to turn the VCR on. Press the VCR buttons shown at the left. If your VCR does not work, program VCR1 or VCR2•LD with a VCR code... - Page 11 VCR 1 Channel: 00 Set VCR 1 Channel to: 4B, 5B 3 or 4 (same as 3/4 switch) A. Press TV to set the remote to control the TV. B. Press MENU•PROG to select the Setup menu. This menu is white.
- Page 12 DISPLAY SKIP C. Press RECORD to start recording. MUTE PREV CH D. Press TV/VCR on the VCR. E. Press TV to set the remote to control the TV. INPUT ANTENNA • CLEAR RESET F. Press CHANNEL up or down to change channels on the TV.
-
Page 13: With Satellite Receiver
Using Your TV and Remote With a Satellite Receiver: Basic Operation You may also be able to use the TV’s remote with the RCA DSS satellite receivers. Refer to your Satellite Receiver owner’s manual to hook up your Satellite Receiver. The remote may need to be programmed for other brands of satellite receivers, but may not operate all models of the brands listed below. -
Page 14: With A Cable Box
If you have a cable box with its own remote, then you may also be able to use the TV’s remote with your cable box. This remote may not operate all models of the brands listed below. Use the codes below or on the sheet packed in with your remote. - Page 15 Autoprogram Channel Memory: 13 Stored Cable/Air: Cable VCR 1 Channel: 00 Cable Channel: 03 A. Press TV to set the remote to control the TV. B. Press MENU•PROG to select the Setup menu. This menu is white. A. Press MOVE...
-
Page 16: With Laserdisc Player
C. Release VCR2•LD. D. Press POWER. If nothing happens, try pressing VCR2•LD and then POWER. A. Tune TV to channel 00, 03, or 04. B. Point the remote at the laserdisc player and press VCR2•LD. C. Press POWER to turn it on. -
Page 17: With Audio Equipment
Use the codes below or on the sheet packed in with your remote. Program the remote for audio equipment Basic Operation Audio Codes RCA/ Dimensia AM/FM...03 CD ...07 Tape ...06 Phono ...05 Aux ...04 A. -
Page 18: Adjusting Your Tv
Adjusting Your TV Overall Picture Follow the steps below to lighten or darken the overall picture without changing the color levels. Select the Controls Menu Highlight Picture Use MOVE adjust the Picture Controls Alarm Adjust Setup Sleep Timer: -:-- Closed Captioning: Off Picture -... -
Page 19: Picture Settings
Adjusting Your TV Picture Settings Follow the steps below to change the picture on the screen to your personal setting. The chart at the bottom of the page explains your options. Select the Adjust Menu Highlight item to change Use MOVE... -
Page 20: Sound Settings
Adjusting Your TV Sound Settings: Stereo and Tone Follow these steps to adjust the Stereo or Tone of your TV. The chart below explains your options. Select the Controls Menu Highlight item to change Use MOVE adjust each item Stereo... -
Page 21: Placing Channels In Memory/Autoprogram
You may want to add or delete a few channels if some stations have weak signals or were off the air when the TV was programmed. Refer to the Add or Delete Channels section below. -
Page 22: Using Advanced Features
Using Advanced Features Setting the Sleep Timer You can set your TV to turn itself off. If you’re watching TV at night and fall asleep, the TV will turn off for you. Set Sleep Timer Add more time Cancel the Timer Controls Alarm Adjust Setup Sleep Timer: –... -
Page 23: Setting The Alarm Clock
Using Advanced Features Setting the Alarm Clock The TV can be set to turn on each day like your alarm clock. You can set it to turn on to your favorite channel at a certain time. You can also set it to turn itself off again. -
Page 24: Selecting A Language
Using Advanced Features Selecting a Language The on-screen displays in this TV can be displayed in three languages: English, Spanish, and Portuguese. When you select a language, most of the displays will be shown on the screen in your preferred language. -
Page 25: Watching Closed Captioning
Watching Closed Captioning Closed captioning displays the audio portion of a program as words on the TV screen. It is useful for the deaf, hearing impaired, or anyone who wants to watch a program without sound. If you have turned Closed Captioning on and it does not appear on the screen, it is not available on the channel you are watching. -
Page 26: Setting Your Tv For Antenna Or Cable
Using Advanced Features Setting Your TV for Antenna or Cable Your TV automatically adjusts this feature when the TV places channels in memory (Autoprogram). Follow the steps below to change the setting as needed. Select the Setup menu Highlight Cable/Air... -
Page 27: References
The CHANNEL up and down and VOL + and - buttons, not only change the channels and volume of the TV, but work like the MOVE buttons when you are in the TV Menu. For details on using buttons with menus, see Menu Basics on page 5. MENU MENU –... -
Page 28: Displays On The Screen
References Displays on the Screen Your TV shows the settings of several features on the screen. To see what features have been set on your TV, press DISPLAY on the remote. Screen Display 12:00 AM Video 00 Alarm Sleep Volume... -
Page 29: Trouble Checks
Make sure component connected to the VIDEO INPUT jacks is turned on if you choose channel 00. Make sure TV is tuned to the same channel as the switch on back of VCR if watching a VCR. Make sure TV/VCR button on VCR is in correct position when using VCR. - Page 30 Alarm Time Checks and Adjustments Press TV to set the remote to control the TV. See buttons on page 6. Remove batteries and hold down one or more buttons for several seconds to drain the microprocessor inside the remote and reset it. Re-install the batteries and try remote again.
-
Page 31: Index
Picture Adjustments...17 Picture Quality...17 Picture Reset...17 Plug in TV...2 Power Buttons...6 Previous Channel Button ...6 Problem Solving ...27-28 Quick Guide to Your TV ...2,3,4,5 Quick Button Guide ...4 References ...25-29 Trouble Checks...27-28 Remote Control Batteries ...2 Buttons ...4,6,7 Tour ...4 With Components ...8-15... - Page 32 EXPORTED BY: 10330 North Meridian Street Indianapolis, IN 46290-1024 ©1995 Thomson Consumer Electronics, Inc. Trademark(s)® Registered Marca(s) Registrada(s) Printed in the U.S.A. TOCOM 15128920 COUNTRY OF ORIGIN: 100% RECYCLED PAPER MINIMUM 50% POST CONSUMER...