Subscribe to Our Youtube Channel
Related Manuals for Dahua Technology DHI-ITALE-160BA
Summary of Contents for Dahua Technology DHI-ITALE-160BA
- Page 1 LED Multifunction Illuminator User's Manual ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.3...
-
Page 2: Foreword
Foreword General This manual introduces the functions and operations of the LED multifunction illuminator (hereinafter referred to as "the Illuminator"). Models DHI-ITALE-160BA Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a high potential hazard which, if not avoided, will result in death or serious injury. - Page 3 User's Manual ● We are not liable for losses incurred due to operating the product in ways that are not in compliance with the manual. ● The manual will be updated according to the latest laws and regulations of related jurisdictions. For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit our official website.
-
Page 4: Important Safeguards And Warnings
User's Manual Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it, and keep the manual safe for future reference. Transportation Requirements ●... - Page 5 User's Manual accessible location for emergency power cut-off. ● Prevent water from flowing into the device and causing damage during on-site installation. Operation Requirements ● Avoid violent collisions. ● Do not constantly use flash for the device while testing it to avoid the risk of the device overheating or becoming damaged.
-
Page 6: Table Of Contents
User's Manual Table of Contents Foreword ........................................I Important Safeguards and Warnings ............................III 1 Introduction ......................................1 1.1 Introduction ....................................1 1.2 Features ......................................1 2 Structure ........................................3 2.1 Appearance ....................................3 2.2 Dimension ..................................... 3 3 Installation ....................................... 4 4 Connecting Cable .................................... -
Page 7: Introduction
User's Manual 1 Introduction 1.1 Introduction ITALE-160BA is an LED illuminator, integrating strobe, continuous light and flashlight. The unique optical design makes it capable of oriented illumination at night, which greatly reduces light pollution of city road and improves traffic safety. The Illuminator supports video and image illumination, meanwhile, integrates camera maintenance. - Page 8 User's Manual The Illuminator supports low electrical level and pulse width triggering. ● Flashlight Duration You can calculate the device product life through the duration of the flashlight shines. ● Flash Counting You can quickly locate the signal interference on site through counting the times of the Illuminator flashes and being triggered (times of external signal input).
-
Page 9: Structure
User's Manual 2 Structure 2.1 Appearance Figure 2-1 Product appearance 2.2 Dimension Figure 2-2 Dimension (mm [inch]) -
Page 10: Installation
User's Manual 3 Installation Step 1 Match the Illuminator with bracket, and then install them on the pole (only upright mount and hang mount). Figure 3-1 Upright mount Figure 3-2 Hang mount Step 2 Connect power cable (ground). For details, see "4.2 Connecting Power Cable". Step 3 Adjust the angle of the Illuminator as needed. - Page 11 User's Manual operate on it when under normal status. You can check the Illuminator status through directly connecting the positive with the negative signal cable of the strobe or flashlight. If it flashes, the Illuminator works.
-
Page 12: Connecting Cable
User's Manual 4 Connecting Cable 4.1 Waterproof Operation Step 1 Wrap the juncture (marked as 2 in Figure 4-1) of the cable core and insulation cover with insulation tape, and then wrap it again with waterproof insulation tape. Step 2 Wrap the naked cable core (marked as 1 in Figure 4-1) with insulation tape, and then wrap it again with waterproof insulation tape. -
Page 13: Connecting Flashlight/Strobe Cable
User's Manual Figure 4-2 Power cable Table 4-2 Description of power cable Function Description Blue: Neutral line. 220 VAC Brown: Live line. 220 VAC Yellow and green: Ground line Yellow: Flashlight + Power cable Blue: Flashlight - Green: Strobe + Gray: Strobe -/GND Red: RS-485A White: RS-485B... -
Page 14: Connecting Rs-485 Cable
User's Manual Figure 4-3 Flashlight/strobe cable connection Step 1 Plug the flashlight + (yellow) and flashlight - (blue) of the Illuminator into the flashlight triggering port F1+/F2+ and F1-/F2- of the camera. Step 2 Plug the strobe + (green) and strobe - (gray) into the strobe triggering port F7+ and F7- of the camera. -
Page 15: Connecting Serial Port
User's Manual Step 2 Connect the RS-485 B (white) cable of two illuminators in parallel circuit, and then connect the 485-B port of the camera. Step 3 Obtain the address of each illuminator. Step 4 Select Setup > ITC > Extra Device > Light (485) Config, and then click Auto Address on the continuous light area. -
Page 16: Configuring Camera
User's Manual 5 Configuring Camera You can configure the parameters of the strobe, flashlight and continuous light on the camera web page. The configuration page might vary with different web baseline. Select the corresponding configuration. 5.1 Configuring External Light Log in to the camera web page and select Setup > ITC > Extra Device > Light Config. Step 1 Step 2 Configure the parameters of the flashlight or strobe. -
Page 17: Configuring External Rs-485 (Strobe)
User's Manual Parameter Description Set the delay time of the flashlight to make sure that the Delay Time camera captures and the flashlight flashes at the same time. The triggering electrical level (high level and low level) of the Burst Mode flashlight. -
Page 18: Configuring External Rs-485 (Continuous Light)
User's Manual Table 5-2 Description of strobe parameters Parameter Description Strobe No. Select strobe number as needed. Select Enable to turn on the selected strobe. Enable Select Yes or No as needed to check the strobe status. Check Status Light Brightness Set the brightness of the strobe under normal working status. - Page 19 User's Manual Parameter Description ● Close: The continuous light stays off. ● Enable: The continuous light stays on. Work Mode ● Auto (recommend): System turns on the continuous light according to time or environment brightness. Light Brightness Set the brightness of the continuous light under normal working status. You need to configure this when setting Work Mode to Auto.
-
Page 20: Updating Program
User's Manual 6 Updating Program You can update the program on the web page of the camera. ● If error happens during updating, you can restart the Illuminator and update again. ● Do not cut off the power supply during update. Plug the RS-485 signal cable of the Illuminator into the A1, B1 port of the camera. -
Page 21: Notes
User's Manual 7 Notes 7.1 Start-up Time ● When powering up the Illuminator, you need to wait for about 13 s for the program to start. System turns on or off the Illuminator based on the environment brightness as configured. ●... -
Page 22: Appendix 1 Cybersecurity Recommendations
User's Manual Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. - Page 23 User's Manual 1024–65535, reducing the risk of outsiders being able to guess which ports you are using. 6. Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel. 7. MAC Address Binding We recommend you to bind the IP and MAC address of the gateway to the equipment, thus reducing the risk of ARP spoofing.
- Page 24 User's Manual ● Enable IP/MAC address filtering function to limit the range of hosts allowed to access the device. More information Please visit Dahua official website security emergency response center for security announcements and the latest security recommendations.
- Page 25 User's Manual...
Need help?
Do you have a question about the DHI-ITALE-160BA and is the answer not in the manual?
Questions and answers