Download
Share
Print this page
  1. Manuals
  2. Brands
  3. G&G Manuals
  4. Lighting Equipment
  5. EDGE
  6. Installation manual

G&G EDGE Installation Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
800.285.6780 sales@ggled.net
EDGE INSTALLATION MANUAL PAGE 1
WARNING
Fixtures must be installed by a qualified electrician in accordance with all applicable national and local electrical
and construction codes and regulations. Please read through this entire document before beginning the
installation.
Remove any fixture from service if water or corrosion is observed inside the fixture. Water and chemicals can
corrode metallic components and damage electrical circuits. Faulted electrical circuits can experience self-
heating which, while unlikely, may present a fire hazard if left unchecked. This heating can also serve as an
ignition source for gasses generated by the corrosion of metals inside of the enclosure. Regularly scheduled
inspections are recommended to ensure safe operation.
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation, or removal.
Electrical Requirements
• Suitable for wet locations.
• Follow all National Electric Codes (NEC) and local codes.
Notes
These instructions cover both the standard EDGE Power/Data Translator (PDT) configuration and PDT
configuration that includes the optional ColorWash controller. The steps which differ between these two
configurations are in separate sections, and it is only necessary to complete the ones that apply to the PDT
being installed.
Customer Service
For technical assistance and installation support please call 800-285-6780 x2 or email support@ggled.net
STRONG.
SIMPLE.
IP68
IMPACT
IP69K
CERTIFIED
C E R T I F I E D
Rev Date 23 0610
COMPACT.
IK10

Advertisement

loading
Need help?

Need help?

Do you have a question about the EDGE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for G&G EDGE

Summary of Contents for G&G EDGE

  • Page 1 • Follow all National Electric Codes (NEC) and local codes. Notes These instructions cover both the standard EDGE Power/Data Translator (PDT) configuration and PDT configuration that includes the optional ColorWash controller. The steps which differ between these two configurations are in separate sections, and it is only necessary to complete the ones that apply to the PDT being installed.
  • Page 2 Supplied Materials G&G EDGE Series Fixtures Leader Cable(s) Jumper Cable(s) Termination Plug(s) Mounting Brackets (Ceiling or Wall) G&G EDGE Power/Data Translator (PDT) [Includes controls, power distribution and drivers.] EDGE Standard Fixture EDGE Leader Fixture Leader Cable Jumper Cable Termination Plug...

  • Page 3: Notice To Installers

    There are 2 different types of fixtures used in the EDGE lighting system. The first “LEAD” (LE) fixture on each leader uses a 6-pin input connector, while all other “THRU” fixtures in each string have 4-pin connectors. THRU fixtures have a gray connector shell on the input end and a black connector shell on the output end, while LEAD fixtures have black connector shells on both ends.
  • Page 4 EDGE INSTALLATION MANUAL PAGE 4 Mounting the EDGE Fixtures • EDGE series wet location fixtures are typically surface mounted (Walls, Soffits, etc.). If mounting to the building soffits, it is recommended to mount the fixtures on the outer edges of the soffits to maximize the distance from the building walls.
  • Page 5 Power Circuits / Wiring / Circuit Breakers The EDGE system is compatible with 120V and 277V single phase power systems. The EDGE system needs to have power supplied to it from the building’s breaker box to the three AC VOLTAGE IN terminals (LINE, NEUT, GRND) at the bottom of the board below the driver fuses.
  • Page 6 EDGE INSTALLATION MANUAL PAGE 6 Pixel Information • EDGE fixtures use 4 DMX channels per pixel in an RGBW configuration for each 2-foot-long pixel, but only the first three channels (RGB) are used (EDGE fixtures only contain red, green and blue LEDs).
  • Page 7 LED Fixture Electrical Connections • The LED Output connectors on the circuit board inside the EDGE PDT are labeled 1A, 1B, 2A, and 2B. • The system layout that is included with the system identifies which leaders connect to which string of lights.

  • Page 8: Dmx Configuration

    Connectivity sections on page 9. Data Input • The DMX connections bring fixture data into the EDGE PDT board and optionally pass the data along to other DMX devices. • Terminal blocks are provided for connecting the three discrete wires in the data cable; these are marked on the board next to the terminals (D+, D-, and COM).
  • Page 9 • Ethernet Network connectivity to ethernet port J1 is required to adjust the settings stored on the controller. Network Connectivity In order to configure the ColorWash portion of your EDGE system, it must have a Port Usage connection to the internet. The connection...