Subscribe to Our Youtube Channel
Related Manuals for Sherwood BOS-450-T
Summary of Contents for Sherwood BOS-450-T
- Page 1 7/22 BOS-450-T Oscillating Belt & Spindle Sander Owner’s Manual 1300 880 996 customer.service@timbecon.com.au...
- Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance and service of your machine. Save this document, refer to it often and use it to instruct others on correct operation. Failure to read, understand and follow the instructions in this manual may result in serious personal injury - including amputation, electrocution or even death.
-
Page 3: Table Of Contents
Contents Introduction Safety Electrical Information Specifications Set Up Operation Maintenance & Care Warranty Contents... -
Page 5: Introduction
Alternatively, you can contact us directly at support@sherwoodtools.com.au Technical Support If you have a question about your Sherwood product that isn’t covered in this manual, please email us directly at support@sherwoodtools.com.au. Introduction... -
Page 6: Safety
Section 1: Safety General Safety Rules For your own safety, please read and understand this instruction manual before installing and operating the machine. Owners Manual: Read and understand this Disconnect the Power First: Always disconnect owners manual before using the machine. the machine from the power supply before making adjustments, changing tooling or Failure to Read This Manual: Failure to adhere... - Page 7 General Safety Rules Use Correct Tool for the Job: Only ever use Unattended Operation: To reduce the risk of the machine for its intended purpose. Do not accidental injury, turn the machine OFF and force it or use any attachment to complete a ensure all moving parts are completely stopped job for which it was not designed.
- Page 8 Specific Rules For The Belt & Spindle Sander 1. This sander is designed to sand wood or 11. When sanding a large workpiece, provide wood-like products only. Sanding or grinding additional support. Do not sand with the other materials could result in fire, injury, or workpiece unsupported.
-
Page 9: Electrical Information
Section 2: Electrical Information Electrical Requirements Extension Cords Power Supply And Motor Specifications: Grounded Tools require a three wire extension cord. Warning: To avoid electrical hazards, fire hazards, or damage to the tool, use proper Double Insulated Tools can use either a two or circuit protection. - Page 10 Guidelines for Using Extension Guidelines & Recommendations Cords for Extension Cords When Using An Extension Cord, be sure to If you are Using An Extension Cord outdoors, use one heavy enough to carry the current be sure it is marked with the suffix “W-A” to your product will draw.
-
Page 11: Specifications
Section 3: Specifications BOS-450-T Oscillating Belt & Spindle Sander Motor 120 V, 60 Hz, 3.5A, 1/2 HP, 11,500 RPM Belt Speed: 1575 FPM Spindle Speed: 2000 RPM Oscillations: 58 OPM Spindle Travel: 5/8 in. Table Tilt: 0 to 45° Sanding Drum Sizes: 3/4, 1, 1-1/2, &... -
Page 12: Set Up
Section 4: Set Up Key Features Work Table Spindle Nut ON/OFF Switch Sanding Belt Sanding Drum w/ Sleeve Sanding Drum Storage Belt Tracking Adjustment Knob Table Insert Spindle Knob Belt Tensioning Lever Dust Port Circuit Breaker Work Stop Throat Plate Storage Spindle Table Tilt Locking Knob Set Up... - Page 13 Inventory Belt Sanding Attachment Table Insert 80-Grit Sanding Belt Throat Plates (4 x 24 in.) (1/2, 3/4, 1, 1-1/2, & 2 in.) Spindle Nut Wrench Spindle Washers (13 mm/10 mm) (5/8, 7/8, & 1-3/4 in. outer diameter) Sanding Drums Hex Nut (3/4, 1, 1-1/2, &...
- Page 14 Set Up Mounting The Unit (Fig. A-B) (Fig. C-D) WARNING: To avoid injury from accidental The base of this machine has four 1/4 inch startups, turn switch OFF and remove the plug mounting holes on the corners of the base. from the power source outlet before making Mount to a benchtop surface to maximize any adjustments.
-
Page 15: Operation
Fig. D1. Once all of these steps have been checked and completed, the sander is ready for operation. If you have a question about your Sherwood product that isn’t covered in this manual, please email us directly at support@sherwoodtools.com.au. Fig. E1. - Page 16 Spindle Sanding Using Spindle Sander Spindle sanding is the preferred method of (Fig. F-G) removing material from inside curves and irregular edges. The oscillating spindle moves up Turn the sander ON and allow it to reach full and down as it rotates to help smooth surfaces speed.
- Page 17 Belt Sanding Outside Curves Belt Sanding Inside Curves (Fig. J) (Fig. L) Turn sander ON and allow it to reach full To belt sand any inside curves, use the rounded speed before applying a load. surface of the large or the small sanding drum wheel.
- Page 18 Adjust The Tracking Of The Bevel Sanding Sanding Belt (Fig. N) The work table has the capacity to tilt from Install the belt sanding attachment and 0 to 45 degrees for sanding bevels on your remove all tools from the sander. workpiece.
-
Page 19: Maintenance & Care
Section 6: Maintenance & Care Maintenance WARNING: For your own safety, turn the WARNING: Any attempt to repair or replace switch OFF and remove the plug from the electrical parts on this tool may be hazardous. electrical outlet before adjusting or performing Repairs should be done by a qualified service maintenance on the belt/spindle sander. - Page 20 Troubleshooting PROBLEM CAUSE Sanding grains easily 1) Sanding belt/sleeve has been stored in the wrong environment. rubs off. 2) Sanding belt/sleeve has been damaged or folded. Deep sanding grooves or scars in 1) Sanding belt/sleeve grit is too coarse for the desired finish. workpiece.
- Page 21 SOLUTION 1) Store sanding accessories away from extremely hot/dry temperatures. 2) Store sanding accessories properly, without bends, folds, or crushing. 1) Use a finer-grit sanding accessory. 2) Sand with the grain of the wood. 3) Reduce pressure on workpiece while sanding. 4) Keep workpiece moving while sanding on the sanding accessory.
- Page 22 Warranty and Service If your Sherwood product has a warrantable fault, please contact the retailer that it was purchased from. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
- Page 24 Notes:...
- Page 25 Notes:...
- Page 26 1300 880 996 customer.service@timbecon.com.au...
Need help?
Do you have a question about the BOS-450-T and is the answer not in the manual?
Questions and answers