Special Safety Rules; Maintenance; Environmental Protection - Ryobi RMT1201 Original Instructions Manual

Safety, performance, and dependability have been given
top priority in the design of your cordless multi-tool.
Intended use
The product is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
You may use this product for cutting and sanding purposes.
Do not use the product in any way other than those stated
for intended use.
WARnInG
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
save all warnings and instructions for future reference.

specIAl sAfety Rules

■ Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
■ Protect your lungs. Wear a face or dust mask if the
operation is dusty.
■ Always wear safety goggles and a dust mask when
sanding, especially sanding overhead.
■ A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
■ When not in use, all tools should be disconnected from
power source.
AddItIonAl BAtteRy sAfety WARnInGs
WARnInG
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
tRAnspoRtInG lItHIuM BAtteRIes
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

MAIntenAnce

■ When servicing, use only original RYOBI replacement
parts. Use of any other parts may create a hazard or
cause product damage.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
■ Always wear safety goggles or safety glasses with side
shields during power product operation or when blowing
dust. If operation is dusty, also wear a dust mask.
■ To avoid serious personal injury, always remove
the battery pack from the product when cleaning or
performing any maintenance.

envIRonMentAl pRotectIon

Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging
environmental-friendly recycling.
led IndIcAtoR
Battery charge
66% - 100%
33% - 66%
< 33%
note: If only the red LED indicator is illuminated, it
means the battery power is low. The battery needs to be
recharged.
BAtteRy oveRloAd pRotectIon
This tool is designed to protect the battery from overloading.
When overloading is detected, the tool will automatically
switch off. To resume operation, switch the tool off and
on again. If the tool fails to operate, it means battery pack
is discharged and should be recharged in a compatible
charger.
English
should be sorted for
led colour
Green + Yellow + Red
Yellow + Red
Red
1
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL