Related Manuals for HURNER CNC ECO 200
Summary of Contents for HURNER CNC ECO 200
- Page 1 User’s Manual CNC ECO 200 The German version of the herein is the original copy, reflected in the translations herein. П HÜRNER SCHWEISSTECHNIK GmbH Nieder-Ohmener Str. 26 35325 Mücke (Atzenhain) Version Februar 2018...
-
Page 3: Table Of Contents
Saving the Reports to a Storage Media ............21 Deleting Data in Memory ................. 22 Keeping Data in Memory ................. 22 Service and Repair..................... 22 Service and Repair Contact................22 Accessories/Parts for the Product ..............23 Version February 2018 HÜRNER CNC ECO 200 User’s Manual... - Page 4 Only the manufacturer and authorized service points are able to make this change. To this end, get in touch with them. HÜRNER CNC ECO 200 User’s Manual Version February 2018...
-
Page 5: Introduction
The development, manufacture, and check of the heating element butt-welding machine HÜRNER CNC ECO 200 has been per- formed with a view to superior operation safety and user-friendliness. The machine was manufactured and checked according to state-of- the-art technology and widely recognized safety regulations, as they are applied. -
Page 6: Owner And Operator Obligations
The operating/ owning organization engages to check at reasonable intervals if the machine is operated by the welders as intended and under proper guidelines of occupational safety. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 7: Intended Use
Understanding the Machine HÜRNER Schweißtechnik GmbH Nieder-Ohmener Str. 26 Nieder-Ohmener Str. 26 This butt-welding machine for plastics can be used both as an on-site D - 32325 Mücke D - 32325 Mücke Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 8: Included Components
When the hazard is cleared, the switch has to be unlocked by turning the pushbutton clockwise. It is also possible to Important move the carriage of the basic machine chassis manually. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 9: Connectors
39 kg Facing Tool 11 kg Heating Element 6 kg Hydraulic & Control Unit 44 kg Carrying and Storage Rack 8 kg Transport Box 30 kg All Reducer Inserts 41 kg Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 10: Overview Of The Welding Process
• After the heating stage, the machine automatically moves the movable carriage apart and the welder has to remove the heat- ing element from in-between the butts. • After the removal of the heating element, the machine automati- cally closes the pipes in on each other. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 11: Operation
— in Rep. No. 00072/00002 the second-to-last line — the actual input voltage and the actual and nominal heating element temperature before and after the slash. Display 4 Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 12: Setting The Default Configuration Of The Machine
“open” position (see Sect. 4.1 and Display 4). If the entered menu selections code is correct, the Configura- Important tion Menu shows on the screen, as in Display 6. HÜRNER CNC ECO 200 User’s Manual Version February 2018... - Page 13 OFF: no automatic removal is controlled by the system even when an automatically removing heating element is used; the welder will have to remove it manually at change-over. Version February 2018 HÜRNER CNC ECO 200 User’s Manual...
- Page 14 Pipe Codes ON / OFF if ON: the code of the pipes, in which the pipe parameters related to welding are contained, must be entered before welding. HÜRNER CNC ECO 200 User’s Manual Version February 2018...
-
Page 15: Entering Traceability Data
The specialty material screens include a menu option “Stan- dard Material” to enable returning to the screen in which they were selected, the screen reproduced in Display 9. Info Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 16: Performing The Welding Process
When pipe alignment is appropriate, move the carriage apart to the far end for the welding proper, by pressing the START/SET key. If needed, the welding process can be aborted by pressing the STOP/ RESET key. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 17: Possibility To Change Welding Parameters
The so-called automode is a tool for monitoring the duration of the bead build-up stage and moving on automatically from the bead build-up to the heating Info stage by decreasing the applied pressure. However, this Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 18: Heating Stage
Display 25 4.5.9 End of Welding A beep signals the end of the cooling time. Furthermore, the green LED is lit to indicate a successful welding process. Confirm the end of HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 19: Printing Label Tags
To call the ViewWeld abstract of a welding report, press the ñ key in the Next Welding screen (see Display 4). Browsing through the saved welding reports is then possible by pressing the or ð cursor Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 20: Aborted Welding Process
Error Heating Pressure Heat-soaking pressure too high, could not be re-adjusted. Error Joining Pressure Joining pressure too high or too low, could not be re-adjusted. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 21: Downloading Welding Reports
Wait for all the selected reports to download and the “Finished” message to appear on the screen. If a problem occurs while the download is in progress, the transmission Version February 2018 HÜRNER CNC ECO 200 User’s Manual... -
Page 22: Deleting Data In Memory
Info A risk assessment under the provisions of the so-called machinery directive 2006/42/EC was conducted for the machine by a qualified person entitled to the performance of such an assessment. HÜRNER CNC ECO 200 User’s Manual Version February 2018... -
Page 23: Accessories/Parts For The Product
(so-called RoHS Directive). Accessories/Parts for the Product Facing Tool Blade for HÜRNER CNC ECO 200 Only genuine spare parts are acceptable. The use of non- genuine parts voids any and all liability and warranty on the part of the manufacturer. - Page 24 Verantwortung, dass das Produkt declare under our sole responsibility that the product заявляем с полной ответственностью, что изделие HÜRNER CNC ECO 200 Heizelement-Stumpschweißmaschine zur Verschweißung von Kunststoffrohren und -formteilen Heating Element Butt-Welding Machine for Welding Plastic Pipes and Fittings Машина...
- Page 25 HÜRNER CNC ECO 200 Máquina de soldar a tope con elemento calefactor para los accesorios termoplásticos Machine à souder bout-à-bout à élément chauffant pour l’assemblage des tubes et raccords en plastique, Máquina de soldar por termfusão com elemento de aquecimento pelas peças termoplásticas,...
Need help?
Do you have a question about the CNC ECO 200 and is the answer not in the manual?
Questions and answers