Related Manuals for RADtec H1501A
Summary of Contents for RADtec H1501A
- Page 1 Model PH is flame heater with stainless steel base Model WPH is flame heater with wicker base Tower Flame Patio Heater In tr tion Man al WARNING: FOR OUTDOOR USE ONLY PLEASE KEEP THE MANUAL FOR FUTURE REFERENCE! - 0 -...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Patio Heater Safety Warnings --------------------------------------------- 1-2 Part List & Hardware --------------------------------------------------------- 3 Exploded View ----------------------------------------------------------------- 4 Patio Heater Assembly ------------------------------------------------------ 4-8 Operating Instructions ------------------------------------------------------- 9 Leak Testing -------------------------------------------------------------------------10 Gas Requirement ------------------------------------------------------------- 10 Connecting To a Gas Cylinder --------------------------------------------- 10 Important Safety Rules ------------------------------------------------------ 11 Maintenance -------------------------------------------------------------------- 11 Servicing ------------------------------------------------------------------------- 12... - Page 3 • Check the tubing or the flexible hose per month and each time the cylinder is changed. • The tubing or the flexible hose must be changed within the prescribed intervals or within one year. • The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged.
-
Page 4: Part List & Hardware
PATIO HEATER PART LIST PART # PART NAME PICT RE REFLECTOR FLAME SCREEN MESH G ARD - PPER MESH G ARD - LOWER S PPORT AR - PPER S PPORT AR - LOWER GLASS T CONNECTOR Glass Tube Connector ER RING RNER ASSEM LY TAN HO SING ASSEM LY CHAIN (ASSEM LED WITH DOOR) -
Page 5: Exploded View
E PLODED IEW... -
Page 6: Patio Heater Assembly
PATIO HEATER ASSEM LY ASSEM LY INSTRUCTIONS • List of Required Tools: Philips Screwdriver • Leak Detection Solution one part detergent and three parts water • em le all n t an olt loo el at ir t Ti ten all onne tion a ter om letion o a em l T i ea e o r wor an in rea e t e ta ilit o t e a... - Page 7 Repeat this step and connect Flame Screen ( ) to other 3 sets of upper Support ars. (See Figure Ⅲ, Ⅳ) STEP : Place Reflector (A) on the Flame Screen ( ) and fix the connection using 4 M5 CAP N TS (AA). STEP : nscrew 8 M5 Screws and Washers ( ) preassembled on top of tank housing assembly ( ).
- Page 8 STEP : Insert 4 projecting ends of each lower Mesh Guard (D) into the seat slots of lower the Support ar (F) as shown in picture. Fix all lower Mesh Guards (D) except the front side. Guard Fastening Plate STEP nscrew 4 Guard Fastening Plates preassembled with the sides of FLAME SCREEN ( ).
- Page 9 < -- STEP : Put Rubber Ring (I) around the burner hole. Connect the 2 Glass Tubes (G) with Connector (H) Hold the whole glass tube assembly carefully. Insert the top end into the bottom hole of the Flame Screen as much as possible.
-
Page 10: Operating Instructions
OPERATING INSTRUCTIONS EFORE FIRST USE AND AFTER E ERY GAS CYLINDER CHANGE THE GAS DELI ERY SYSTEM MUST E PURGED OF AIR EFORE IGNITING! TO DO THIS TURN THE CONTROL KNO COUNTER CLOCKWISE TO THE PILOT SETTING PRESS KNO IN AND HOLD FOR MINUTES EFORE ATTEMPTING IGNITION ATTERY REPLACMENT Remove impulse ignition cap from urner Assembly ( ) by turning cap counterclockwise. -
Page 11: Leak Testing
LEAK TESTING NE ER USE A NAKED FLAME TO CHECK FOR LEAKS NE ER LEAK TEST WHILE SMOKING The gas connections on this appliance are leak tested at the factory prior to shipment. This appliance needs to be periodically checked for leaks. and an immediate check is required if the smell of gas is detected. -
Page 12: Important Safety Rules
IMPORTANT SAFETY RULES For use outdoors or in amply ventilated areas. An amply ventilated area must have a minimum of 25% of the surface area open. The surface area is the sum of the walls surface. The use of this appliance in enclosed areas can be dangerous and is PROHI ITED. -
Page 13: Servicing
• Please consult your local dealer for servicing this appliance and replacement of its parts. The servicing of the appliance should be carried out only by authorized personnel. • Caution: do not use unauthorized parts or components for this appliance, only use original equipment replacement parts and components. -
Page 14: Troubleshooting
TROU LESHOOTING IF THE PRO LEM IS: AND THIS CONDITION E ISTS: THEN DO THIS: Cylinder valve is closed Open valve lockage in orifice or pilot tube Clean or replace orifice or pilot tube Open gas line and bleed it (pressing Air in the gas line control knob in) for not more than Pilot won t li... -
Page 15: Technical Data
ID number located on the unit. The order number and ID ser e as your arranty numbers and must be retained. RADtec ill offer no arranty ser ice ithout these numbers. RADtec arrants this product and its parts against defects in materials or orkmanship for (1) year parts and labor (residential use) and (1) year parts and labor (commercial use) from the original ship date.
Need help?
Do you have a question about the H1501A and is the answer not in the manual?
Questions and answers