Traxxas E-MAXX BRUSHLESS EDITION 39087-3 Owner's Manual
  1. Manuals
  2. Brands
  3. Traxxas Manuals
  4. Motorized Toy Car
  5. E-MAXX BRUSHLESS EDITION 39087-3
  6. Owner's manual
Traxxas E-MAXX BRUSHLESS EDITION 39087-3 Owner's Manual

Traxxas E-MAXX BRUSHLESS EDITION 39087-3 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL 39087-3
owner
s manual
'

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E-MAXX BRUSHLESS EDITION 39087-3 and is the answer not in the manual?

Questions and answers

Related Manuals for Traxxas E-MAXX BRUSHLESS EDITION 39087-3

Summary of Contents for Traxxas E-MAXX BRUSHLESS EDITION 39087-3

  • Page 1 MODEL 39087-3 owner s manual ’...
  • Page 2 MODEL this manual. TUNING ADJUSTMENTS Thank you again for going with Traxxas. We work hard every day to assure you the highest level of customer satisfaction possible. MAINTAINING We truly want you to enjoy your new model! YOUR MODEL...

  • Page 3: Before You Proceed

    6250 Traxxas Way All of us at Traxxas want you to safely enjoy your new model. Operate your model. Failure to follow these instructions will be considered model sensibly and with care, and it will be exciting, safe, and fun for you and McKinney, TX 75070 abuse and/or neglect.
  • Page 4 No previous experience with radio controlled models is required. • Nickel Metal Hydride batteries must be recycled or disposed of properly. use. Traxxas does not recommend that anyone under the age of 14 use or Models require a minimum of setup, maintenance, or support equipment.

  • Page 5: Tools, Supplies And Required Equipment

    R/C toolbox: • Safety glasses • Traxxas Ultra Premium Tire Glue, part #6468 (CA glue) • Hobby knife • Side cutters and/or needle nose pliers Foam battery...
  • Page 6 E-MAXX BRUSHLESS EDITION OVERVIEW Half Shaft Traxxas High- Electronic Speed Control Hex Hub Pivot Ball Axle Carrier Current Connector Pinion Gear Toe Link Battery Hold-Down Toe Link Battery Front Suspension Arm Spur Gear Rear Body Mount Motor Front Body Mount...

  • Page 7: Quick Start: Getting Up To Speed

    QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. The Quick Start Guide is not intended to replace the 1.

  • Page 8: Radio System

    Cogging - Cogging is a condition sometimes associated with brushless motors. Typically it is a slight stutter noticed when Your model includes the latest Traxxas TQi 2.4GHz transmitter with Applying the Decals accelerating from a stop. It happens for a very short period as Traxxas Link ™...
  • Page 9 When flow is constricted, energy is converted to heat and is IMPORTANT RADIO SYSTEM PRECAUTIONS lost. Traxxas power systems are optimized to reduce electrical • Do not kink the receiver’s antenna wire. Kinks in the antenna wire resistance and the resulting power-robbing heat.
  • Page 10 Wiring Diagram Your model is equipped with the TQi 2.4GHz transmitter with the Traxxas Link Wireless Module. The transmitter has two channels for controlling your throttle and steering. The receiver inside the model has 5 output channels. Your model is equipped with two servos and an electronic speed control.
  • Page 11 INSTALLING TRANSMITTER BATTERIES CHARGING THE BATTERY PACK Your TQi transmitter uses 4 AA batteries. The battery The Traxxas Battery Charger is a fully featured NiMH (Nickle Metal The included charger is compartment is located in the base of the transmitter.
  • Page 12 Your model’s included battery are located in your instructions package. The spacers are shaped pack is equipped with Traxxas 2. Install the battery pack with the battery to conform to the chassis. There is a right and a left. Test fit them to Battery iD.
  • Page 13 (center) point of the steering channel. forward to apply brakes. Note: Traxxas Stability Management (TSM) must be completely Once stopped, return the turned off while adjusting steering trim. See page 14 for TSM throttle trigger to neutral.
  • Page 14 4. Operate the controls on the transmitter once again to be sure that into your Traxxas model by helping the model responds correctly. you to maintain control of the vehicle in low-traction situations.

  • Page 15: Adjusting The Electronic Speed Control

    Drive with TSM on and off to test how it is making your control of the to 70/30, you will need to reprogram the speed control. Follow these 0.0003 Ohms per phase vehicle easier and more precise. For more information, visit Traxxas. instructions to reprogram the speed control: Brake : com/tsm.

  • Page 16: Driving Your Model

    DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on 2. Drive normally. The slipper clutch should slip momentarily driving and making adjustments to your model. Before you go on, when accelerating aggressively on high-traction surfaces (you here are some important precautions to keep in mind.
  • Page 17 Do not use LiPo batteries in wet conditions. • Use batteries with the highest mAh rating you can purchase. • The Traxxas TQi transmitter is not water resistant. Do not subject • Use a high-quality peak-detecting charger. it to wet conditions such as rain.
  • Page 18 DRIVING YOUR MODEL Before Running Your Vehicle in Wet Conditions 4. Blow off the truck with compressed air (optional, but recommended). 1. Consult the section “After Running Your Vehicle in Wet Conditions” Wear safety glasses when using compressed air. before proceeding. Make sure you understand the additional 5.
  • Page 19 The excess wire will be bundled inside the receiver box. Label which wire is for which channel. 4. Apply small bead of silicone grease (Traxxas part #1647) to the wire clamp. 5. Install the wire clamp and tighten the two 2.8x8mm cap screws securely.

  • Page 20: Tuning Adjustments

    TUNING ADJUSTMENTS SUSPENSION TUNING We recommend using two-hole pistons with a range of oil viscosities from 30W to 50W Adjusting the Pivot Ball Caps For easier access to the (available from your hobby shop). The thinner The pivot ball caps should be adjusted rear-most shock mounting viscosity oils (30W or less) flow with less so that the pivot balls operate freely in...
  • Page 21 (A) to position (B). position of the shocks will allow for lower shock progression and the soft, plush feel that’s characteristic of a Traxxas Maxx Truck. Ride height is not affected by changes in the upper shock mounting position.
  • Page 22 (the direction is same The suspension pivot balls located in the axle at all four corners). Note that Traxxas cannot recommend the use of other non-Traxxas wheels carriers adjust the static camber. The pivot the groove in the hex indicates with different specifications.
  • Page 23 TUNING ADJUSTMENTS MOTOR AND GEARING Adjusting Gear Mesh Gearing Compatibility Chart: The chart below shows a full range Incorrect gear mesh is the most The E-Maxx is equipped from the factory with a 68-tooth spur gear of gear combinations. This does NOT common cause of stripped spur and 17-tooth pinion gears.
  • Page 24 If you are using aftermarket servos, it is important to use servo center line of the chassis (pointing to the rear of the truck). horns designed for E-Maxx. Optional steering servo horns are sold separately for use with non-Traxxas servos. Center Drag Link 89.5mm...

  • Page 25: Maintaining Your Model

    5. Check the mounting of the receiver and servo(s) and overtightening. If the bottom of the shock is leaking, then it speed control. is time for a rebuild. The Traxxas rebuild kit for two shocks is 6. Check the tightness of the wheel nuts with a wrench. part #2362.

  • Page 26: Tq I Advanced Tuning Guide

    (0.5 sec on / 0.5 sec off) the module with Traxxas Link App. to and what settings were used for each--up to 30 models total! Traxxas Link See page 13 for information on how provides a visual interface to name the models, customize their settings,...
  • Page 27 The illustrations below show how this works. (set to Traxxas Stability Management (TSM) by default, see page 14). knob. This prevents the model from Experiment with the settings and features to see if they can improve accidentally running away.
  • Page 28 This is especially handy if you operate The TQi transmitter allows you to choose the limit of the servo’s multiple vehicles with a single transmitter via Traxxas Link™ Model travel range (or its “end point”) independently for left and right Memory.
  • Page 29 Model Lock 1. Switch on the transmitter and receiver you wish The Traxxas Link Model Memory feature can store up to thirty to delete. models (receivers) in its memory. If you bind a thirty-first receiver, Traxxas Link Model Memory will delete the “oldest” receiver from 2.
  • Page 30 Transmitter is restored to default Press Delete Model C onfirm Deletion Two Blinks Green One Blink Red *Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).
  • Page 31 ADVANCED TUNING GUIDE Set Multi-Function MENU TREE FORMULAS knob for STEERING Press/hold MENU Press SET Press SET to confirm Press/hold MENU SENSITIVITY (Expo) To select functions and make adjustments to the TQi transmitter without green LED blinks red LED blinks green LED blinks (x8) returns to driving mode referencing the menu tree, turn your transmitter on, find the function in the...
  • Page 32 Android and Google Play are trademarks of Google Inc. iPad (3rd generation and later) iPhone 5C The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Traxxas is under license. iPad mini iPhone 5S 151116 39087-3-OM-EN-R01 Other trademarks and trade names are those of their respective owners.

Table of Contents