Cautions And Warnings - Fortinet FortiGate 60C-LENC Quick Start Manual

Cautions and Warnings

Please review the following cautions and warnings.
Environmental and mounting specifications
Operating temperature: 0 - 40°C (32 - 104°F)
Storage temperature: -25 - 70°C (-13 - 158°F)
Humidity: 20 to 80% non-condensing
Operating Altitude: <2250m (7400ft)
Elevated Operating Ambient: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of
air flow required for safe operation of the equipment is not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connections to the
branch circuit (e.g. use of power strips).
Federal Communication Commission (FCC) – USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if it is not installed and used in accordance
with the instruction manual, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment
Page 8
Industry Canada Equipment Standard for Digital Equipment (ICES) –
Canada
CAN ICES-3 (B) / NMB-3 (B)
European Conformity (CE) - EU
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Grounding
Ensure your Fortinet product is connected and properly grounded to a lightning and surge
protector. WAN or LAN connections that enter the premises from outside the building should
be connected to an Ethernet CAT5 (10/100 Mb/s) surge protector.
Shielded Twisted Pair (STP) Ethernet cables should be used whenever possible rather than
Unshielded Twisted Pair (UTP).
Do not connect or disconnect cables during lightning activity to avoid damage to your
Fortinet product or personal injury.
Electrostatic discharge (ESD) can damage Fortinet equipment. Only perform the procedures
described in this document from an ESD workstation. If no such station is available, you can
provide some ESD protection by wearing an anti-static wrist strap and attaching it to an
available ESD connector or other bare metal object.
Note: For DC installations, a readily accessible disconnect device shall be incorporated in the
building installation wiring.
Caution: For devices that contain a battery there is a risk of explosion if battery is replaced by
an incorrect type. Recycle used batteries according to your local regulations.
Bureau of Standards Metrology and Inspection (BSMI) – Taiwan
The presence conditions of the restricted substance (BSMI RoHS table) are available at the
link below:
https://www.fortinet.com/bsmi
Page 9