Advertisement
Two-channel Mic&Guitar Interface For DSLR cameras, camcorders, iOS and Android devices
The Saramonic SmartRig+ is a microphone/guitar interface for recording sound.
It allows you to connect professional microphones/guitars to create music with your iPhone, iPad, iPod touch and Android devices, or record quality audio to your DSLR cameras and camcorders.
The SmartRig+ makes your recording work much easier. It provides 48V phantom power for microphones and 3.5mm headphone output for real-time monitoring. The two gain control thumbwheels make it easy to set precise levels.
Frequency Response | 20 Hz to 20 Khz, +/-0.5 dB |
THD | less than 0.01% @ 1 kHz, -30 dBu input |
SNR | 80 dB @ 1 kHz, -30 dBu input |
Input1 | 1x XLR mic input |
1 x 1/4" (6.35mm) guitar input | |
1 x 1/8" (3.5mm) input" | |
Input2 | 1 x XLR mic input |
1 x 1/4" (6.35mm) guitar input | |
1 x 1/8" (3.5mm) input" | |
Output | 1 x 1/8" (3.5mm) CAB LINE |
Phone OUT | 1 x 1/8" (3.5mm) jack |
Gain | +20 dB to -∞ |
Phantom Power | 48V power supplies |
Power Requirements | 9V alkaline or lithium battery |
Dimensions | L 120 x W 40 x H 40 mm |
Weight | 130g (excluding battery) |
Input 1:
For Microphone:
One balanced XLR input
One 1/8" (3.5mm) mono input
For Guitar:
One 1/4" (6.35mm) mono standard input
Input 2:
For Microphone:
One balanced XLR input
One 1/8" (3.5mm) mono input
For Guitar:
One 1/4" (6.35mm) mono standard input
Note: Other instruments with 1/4'' (6.35mm) input connector can also be used with the SmartRig+.
M/S switch
Select mono/stereo output mode
When recording on one channel, use the mono (M) setting. The signal will be sent to both left and right channels. When recording on two channels, use the stereo (S) setting. The level of each channel can be controlled individually.
and Control Knobs
Adjust the signal level of each channel to the optimum recording levels.
Knob controls the volume of input group 1 and knob is for input group 2.
Camera/Phone Switch
When connect to a camera, please slide to .
When connect to a smartphone, please slide to .
LED Indicator
When turn on the SmartRig+, the green indicator is on.
When choose +48V phantom power, the red and green indicators are both on.
When it is low battery, the red and green indicators will be dim.
ON/OFF/+48V Switch
Select the ON/OFF switch to turn on/ off the SmartRig+.
Select +48V phantom power for microphones that require phantom power to operate.
Please notice that only the XLR inputs offer +48V phantom power, the 1/8" (3.5mm) mic inputs do not offer +48V phantom power.
Headphone Jack
Monitor the audio from inputs.
Output
1/8" (3.5 mm) output cable to smartphone/camera.
Battery Compartment
Operates on one 9V alkaline or lithium battery (not included).
1/4" Female Screw
Compatible with iPhone/iPad/iPod touch, Android devices, all DSLR cameras and camcorders with 3.5mm mic input connector.
Any types of microphones: Dynamic, Ribbon, or Condenser. Guitars: All guitars with 6.35mm input connector.
The SmartRig+ ×1
Velcro Strip ×1
User Manual ×1
Warranty Card ×1
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Saramonic SmartRig+ Two-channel Mic&Guitar Interface Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the SmartRig+ that isn't answered in the manual? Leave your question here.