Table of Contents
Advertisement
PREPARING THE BRITA
CARTRIDGE
®
1.
Remove the cartridge from its wrapping (it is normal for the
cartridge to appear moist during storage).
2.
Immerse the cartridge in cold tap water and shake gently to
remove any air bubbles. There is no need to pre-soak this
cartridge before use.
3.
Lift the complete lid off your HotCup
remove the filter funnel. Insert the cartridge into the filter
funnel and push it firmly into place. When correctly fitted,
the cartridge should remain in place when the funnel is
turned upside-down.
4.
Fill the filter funnel with cold tap water up to the MAX mark
and allow it to filter through discarding the water. Repeat
this process, again discarding the water.
5.
The BRITA
cartridge is now ready for use. You do not
®
need to keep the filter cartridge immersed in water.
Refit the filter funnel and filter into your HotCup
dispenser. Replace the lid.
6.
Always make sure that you have spare cartridges to hand.
When buying new cartridges look for the BRITA
the cartridge packaging.
7.
When it is time to replace the BRITA
4 weeks use, simply grip the top of the cartridge and
pull upwards to remove. BRITA
recyclable. Visit www.brita.co.uk or call the BRITA
Care team on 0344 742 4800 for further information on
participating retailers.
8.
Repeat steps 1-5 with a new cartridge.
6
VKT241_23EM1 (UK).indd 6-7
VKT241_23EM1 (UK).indd 6-7
™
water dispenser and
™
water
logo on
®
filter cartridge after
®
cartridges are 100%
®
®
BEFORE USING YOUR INSTANT HOTCUP™ WATER DISPENSER FOR THE
FIRST TIME
•
Remove your HotCup™ water dispenser carefully from the box. Remove any
packaging and promotional material and position your HotCup™ water dispenser on
a dry, level, secure work surface away from the edge.
•
Follow the instructions below and discard the first full tank of water. This will remove
any residues that may remain from the manufacturing process.
•
Fit the filter funnel and the BRITA
water filter—see pages 6.
®
USING YOUR INSTANT HOTCUP™ WATER DISPENSER
Always position your HotCup
water dispenser in such a way that the start button
™
cannot be accidentally operated, especially by children. As you use your HotCup
water dispenser, always use care when handling your HotCup
1.
Lift the lid from the water tank and place on the counter top. You can either fill your
tank via a jug or remove the water tank and take it to the water tap to fill.
2.
Fill the filter funnel from your cold tap up to the raised ledge on the outside of the
main water tank. Allow the water to filter through into the water tank. Repeat until
the water level in the main tank is no higher than the MAX marking on the water tank.
3.
Place the lid on the water tank. If you filled at the tap, replace the water tank onto the
main body.
4.
Connect your HotCup™ water dispenser to the mains supply socket and switch the
machine on at the wall. You will hear an audible beep and the control panel will illuminate.
5.
Place a suitable cup or container underneath the dispensing nozzle. With the variable
temperature and dispense the Instant HotCup™ can be used for tea, coffee, hot
chocolate, and any food items where hot or boiling water is required.
WARNING: Never operate your HotCup™ water dispenser without a cup or
suitable container placed below the dispensing nozzle.
SETTING YOUR DISPENSE VOLUME
6.
You can select one of the four pre-set volumes. Choose 200ml or 300ml for various
teas and coffees, or 600ml and 1400ml for larger containers and meal prep needs.
To adjust the dispensing volume touch the 'VOL' icon – this will illuminate 200ml –
select your volume by rotating the control dial clockwise to scroll through 200ml,
300ml, 600ml or 1400ml. When you have selected the right volume touch the 'VOL'
icon again to lock in your selection.
NOTE: If the 'VOL' icon is not selected, the machine will be locked after 60seconds of
no operation.
™
water dispenser.
™
7
2023/3/8 09:39
2023/3/8 09:39
Advertisement
Table of Contents
