Maxwell MW-3503 - Fan Manual

DESCRIPTION

1. Front safety grid
2. Blades
3. Rear grid
4. Body rotation button
5. Fan body
6. Body fixing screw
7. Rod
8. Telescopic stand clamp
9. Overlay
10. Stand
11. Control panel
12. Rear lid fastening nut
13. Clamp
14. Support

ATTENTION!

• Read these instructions carefully before switching on the unit.
• Before using the unit for the first time, make sure that an electricity supply corresponds to the voltage of current specified on the body of the unit.
• Abide special safety tips when children or disabled persons use the unit.
• Do not move, hang up or carry the unit by the power cord.
• To unplug the fan press the "OFF" button on the control panel, and pull the plug out of the socket.
• Do not loop the cord over the fan. It can cause the cord breakage or damage its connection.
• Do not use the fan if the power cord or the plug is damaged or if the fan works irregularly, fell or is damaged. Apply to a service center for testing and repair of the unit.
• Do not use the fan outdoors.
• Do not switch on the fan if the protective grids are not installed.
• Place the fan on the flat stable surface.
• Do not use the fan in bathrooms or similar places.
• Do not place the fan in places, where it can fall in a bath or other container, filled with water.
• If some water gets on the fan, be-fore touching it you should unplug it in order to avoid risk of getting electric shock.
• Do not insert foreign objects into the grids of the fan in order not to get injuries or damage of the unit. Do not touch rotating elements of the fan while it is operating.
• Always unplug the fan if it is not being used.
• The fan is intended only for house-hold usage.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

FAN ASSEMBLY

The fan is supplied disassembled. Do not plug the unit into the mains, if it is not completely assembled.

• Assemble the support (14), by set-ting one part on the other one.
• Unscrew four fastening screws from the support (14).
• Set the stand (10) on the support (14) and fasten it with four fastening screws.
• Put the overlay (9) on the stand.
• Extend the rod (7) from the stand (10) at the desired height and fasten it with the clamp (8).
• Put the body of the fan (6) on the rod (7) and fasten it with the clamp (6).
• Put the rear grid (3); provide that the ledges on the fan body (6) match the openings on the grid, and the carrying handle is above. Fasten the grid with the nut (12), rotating it clockwise.
• Set the blades (2) on the electro-motor shaft and fasten them with the screw.
• Put the front grid (1) on the rear grid (3); fasten the grids with the clips (13).
• The fan is ready for operation.

OPERATION

Before using the unit for the first time, make sure that an electricity supply corresponds to the voltage of current specified on the body of the unit.

• Insert the plug into the socket.
• Select the desired operation mode of the fan by pressing the buttons on the control panel (11):
  0 – off.
  1 – low speed of air flow.
  2 – medium speed of air flow.
  3 – high speed of air flow.

BODY ROTATION FUNCTION

Press the (4) button to switch on the operating mode with the 90° rotation. To stop rotation, lift the (4) button, pulling it upwards.

To change the tilt angle of the fan, loose the screw (6), set the required tilt angle, and then fasten the screw.

CLEAN AND MAINTENANCE

• Before cleaning, unplug the unit, by pressing the "0" button on the control panel (11) and take the plug out of the socket.
• Never use liquid detergents and abrasive substances to clean the unit.
• Wipe the unit with a soft dry cloth.
• If you need to clean the blades, remove the front grid (1), unscrew the screw (13), remove the blades and then wipe them with a dry cloth.
• Set the blades (2) and the front grid (1) on their places.
• Do not immerse the fan into water or other liquids. Provide that liquids do not get into the body of the fan in order not to damage it and not to get risk of electric shock.
• Keep the fan in a dry cool place.

SPECIFICATIONS

Power supply: 220-240 V ~ 50 Hz

Power: 35 W

Diameter: 16" (40 cm.)

3 speed modes

The manufacturer shall reserve the right to change the specification of the appliances without preliminary notice.

Service life of appliance - 5 years