Advertisement
#,
#mw*rem
ffiffiffiffiffiffiwffiffiffi ffiffiffiw$ffiffi
VB9622ATO1
Check the following points once
again.
':;:r''i:r'irrr:r
;:L.ri.i':rl.
Periodic maintenance
is
required
in
order
to
maintain
the
unit's continued
excellent
performance. After a period
of
time the Video heads
will
require replacement.
lf
cleaning
or
replacement of
the
Video heads
is
required,
this
service should be performed
by
an
authorized
Video
System Service
Center.
Tioubles
Coriections,t.
No power
...
No operation starts when
operation
buttons are pressed
...
.
Check that
the
Power Plug
is
completely connected
to
an
AC
Ouflet.
o
Check that
the
POWER Button
is
set
to
"ON".
o
Check
the
DEW lndicator.
lf it is
displayed,
the
unit
will
not
operate.
(p.
36)
s]{,
;*Fft}iF€s3
&}.;#
p{_AY
*A#K
Troubles,,,
Correetions
TV
programs can't
be
recorded
Timer Recording
can't
be
performed
...
There
is
no playback picture, or
the
playback picture is noisy or contains
streaks...
During slow-motion playback,
the
picture shows blurred action
...
During special effects playback,
the
picture may contain some
verlical
jitter when using a
TV
which
has
Automatic Verlical Hold
Control
Switch
...
lf
the
top of
your playback
picture
waves back
and
forth excessively
...
o
Check
the
connections between VCR, external antenna and
your
TV.
o
Make sure that
the
receiving channel of
the VCR is
memorized.
(p.
34)
.
Check that the ANTENNA SYSTEM SELECT Button
is set
to
meet
your cable
TV
system. (p.
33)
o
Make sure that
the
small
tab
on
the
back
of the
cassette
is
still
intact. (p.
41)
o
Make sure that there are no cables connected
to
the Video
and
Audio-lnput Connectors. (p.
32)
r
Set
the
recording start
time
and recording length
correcily.
(p.23-28\
o
Make sure that the TIMER Button
is set.
(p.
25)
o
lf
there
is
a power interruption before or during
a
Timer Recording,
the
Timer
may lose its preset time memory and the Timer Recording
will
not be
performed.
o
Select the same channel
on
your TV
as
that
of
the
CH
3/4 Switch
on
the
VCR.
(p
15)
o
Set
the
VCR/TV
Selector
to "VCR". (p. t5)
o
Check
that
channel
3 or 4 of TV is
properly adjusted. (p.
3)
.
Adjust the TRACKING CONTROL slowly
in
either direction. (p.
14)
o
Use
the Slow Tracking Control.
(on
the Wireless Remote Control).
(p.
t
4)
o
ln
that case,
set
the TV's Vertical Hold Control Switch
to
MANUAL
position
(if
applicable) and then adjust vertical hold
control.
o Because the VCR playback signal
is
not
as
stable
as
an off-the-air
TV signal, you might experience the following symptom on your TV
screen: "Top of TV screen
is
bent or unstable when VCR
is
played
back. This symptom
is
more noticeable when
a
pre-recorded tape,
recorded
by
another VCR,
is
played back." To solve this problem,
locate
the
horizontal hold control on your TV. Turn
it
slowly to correcl
the wavy picture.
lf
your TV does not have the horizontal hold control
or adjusting the control does not help, some modifications have to
be
made
to
the
TV
set. Technically
this is
called "Horizontal
AFC
time constant
change."
lf such a problem is noticed, please contact
your local
TV
service center. (Some nominal service charges
are
required.)
-42-
Advertisement
