Crivit 14131 - LED Bike Light Set Manual

Introduction

List of pictograms used
	Read the instructions!
	Danger to life and risk of accident for infants and children!
	Observe the warnings and safety notices!
	Caution! Explosion hazard!
	Dispose of the packaging and product in an environmentally-friendly manner!
	Environmental damage due to incorrect battery/rechargeable battery disposal!

Intended use

This product is suitable for lighting the roadway whilst cycling. The LED Bicycle Light Set is approved as exclusive lighting for all bicycles. Light distribution must not be impaired by other bicycle parts or luggage. The product is intended for outdoor use. Any use other than the aforementioned or any product modification is prohibited and can result in injuries and product damage. The manufacturer is not liable for damages resulting from improper use. This product is not intended for commercial use.

Parts Description

1. Headlight bracket
2. Reducer rubber
3. Headlight bracket retaining screw
4. Headlight on/off switch
5. Headlight battery/rechargeable battery control light
6. Head lamp battery compartment
7. Headlight
8. Headlight angle adjustment screw
9. Headlight lock
10. Tail light bracket
11. Tail light lock
12. Tail light bracket rubber tab
13. Tail light on/off switch
14. Tail light battery control lamp
15. Tail light
16. Tail light retaining screw
17. Battery cover

Scope of delivery

Technical Data

Note: Please only use alkaline batteries or similar 1.2 V rechargeable batteries.

Safety instructions

• 
  DANGER TO LIFE AND RISK OF ACCIDENT FOR INFANTS AND CHILDREN!
  Never leave children unsupervised with the packing material due to the suffocation hazard posed by swallowing parts thereof. Children frequently underestimate the dangers.
• Always keep the product away from children. This product is not a toy!
• This product is not intended to be used by persons (including children) with impaired physical, sensory or mental capacity, or lacking experience or knowledge unless supervised by a person responsible for their safety. Please note, damages caused by incorrect handling, non-compliance with the operating instructions or interference with the device by unauthorised individuals are excluded.
• Never take the product apart. Improper repairs may result in considerable danger to the user. Repairs should only be carried out by specialist personnel. The LED lights are not replaceable.

Safety advice concerning batteries/rechargeable batteries

• 
  EXPLOSION HAZARD!
  Never recharge the batteries!
  
• Remove batteries during extended periods of non-use.
• When inserting the battery ensure the polarity is correct! This is shown in the battery compartment.
• If necessary, clean the battery and device contacts before inserting the battery.
• Remove spent batteries immediately from the device. There is an increased risk of leaks!
• Always replace all the batteries at the same time.
• Do not mix alkaline batteries and rechargeable batteries.
• Never mix old and new batteries.
• Do not dispose of battery/rechargeable batteries in household waste!
• Every consumer is legally obliged to dispose of batteries/rechargeable batteries in the proper manner!
• 
  EXPLOSION HAZARD!
  Keep battery/rechargeable batteries away from children, do not throw batteries/rechargeable batteries into fire, do not short-circuit and do not take apart.
• Failure to observe this notice may result in deep discharging the batteries. This poses a risk of leaking.
• If the batteries have leaked inside the product, please remove them immediately to prevent product damage!
• Avoid contact with the skin, eyes and mucous membranes if fluid has leaked from the batteries / rechargeable battery. In the event of contact with battery acid, thoroughly flush the affected area with clean water and seek immediate medical attention.
• Never recharge single-use batteries! Explosion hazard!
• Note: If the red rechargeable battery/battery control light on the headlight or the tail light lights up, please replace the batteries or recharge the rechargeable batteries immediately.
• Please note, once the battery indicator lights up, the lights no longer comply with the Road Traffic Act.

Installation

Installing the headlight

• Unscrew the retaining screw from the bracket .
• Position the bracket in the desired location on the handlebar. If necessary, use the reducer rubbers to ensure an optimal fit.
  
• Reinstall the retaining screw .
  
• Tighten the screw hand tight. To prevent damage, do not use tools for this step.
• To adjust to the optimal angle to the direction of travel, loosen the angle adjustment screw 2–3 turns using a cross-tip screwdriver.
• Adjust to the desired angle and tighten the angle adjustment screw .
• Slide the headlight into the bracket until you hear it lock into place.
• To release, press the headlight lock and slide the headlight forward out of the bracket .
  
  ATTENTION! Routinely verify the headlamp adjustment. The light cone must point straight ahead, in the direction of travel, and must not be adjusted too high so as not to blind oncoming traffic.

Inserting the batteries in the head lamp

• Turn the front part of the head lamp until the small arrow is in the „open" position.
• Remove the battery cover .
• Insert the batteries (4 x AA, 1.5 V) in the battery compartment . Ensure the correct polarity.
• Then reassemble the head lamp .

Installing the tail light

• Secure the bracket to the seat post or the rear cross-bar using the rubber tab . Be sure there are no objects in front of the tail light .
  
• Tighten and hook in the rubber tab .
• Loosen the retaining screw ont he bracket and adjust to the desired angle.
• Then tighten the screw. Tighten the screw hand tight. To prevent damage, do not use tools for this step.
• Slide the tail light into the bracket until you hear it lock into place.
  
• To release the tail light , pull down on the tail light lock and slide off the tail light .
  ATTENTION! The tail lamp must be installed and adjusted so the reference axis is parallel to the median longitudinal plane of the vehicle and parallel to the road.

Inserting batteries into the tail light

• Slide the battery cover off to the back.
  
• Insert the batteries into the tail light (2 x AAA 1.5 V). Ensure the correct polarity.
  
• Then reassemble the light.

Switching on / off

The headlight has three brightnesses.

Cleaning and Care

• Never fully immerse the lights. Do not use corrosive or abrasive cleaning agents. Doing so will damage the lights.
• Clean the LED bicycle light set with a slightly damp, lint-free cloth.

GB
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: +49 2 51 132 37 57
E-Mail: gb@klb-service.eu
www.klb-service.eu

IE
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: +49 2 51 132 37 57
E-Mail: ie@klb-service.eu
www.klb-service.eu

NI
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: +49 2 51 132 37 57
E-Mail: ni@klb-service.eu
www.klb-service.eu

Documents / Resources

References

• KLB-Information

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Crivit 14131 - LED Bike Light Set Manual