Viessmann 6366 Operation Manual page 4

2. Introduction
This model uses SMD LEDs to produce light matching the lamp
model. Low heat build-up and power input. Nearly unlimited
lifetime of the LEDs, so no more change is required.
3. Mounting
- Remove the lamp carefully from the package.
- Check function before mounting.
- Drill a hole (Ø 1.5 mm) into a wall for mounting the rope
suspension.
- Drill a hole (Ø 2 mm) into the opposite wall to insert the
connection cables and to fasten the second rope suspension.
- Insert the connection cables into the holes and fasten the
rope suspensions (fig. 1). Guide the cables through the
recess in the ropes.
- Tension the retaining rope and fasten the two ends with knots
or glue.
4. Connection
Caution:
Resistor and diode at the cables are needed for proper
function of the LED model. Never cut them off! Never cover
resistor or diode with insulation material, because they have
to be cooled by surrounding air!
While connecting the cables, leave a loop of about 2 – 3 cm
length below the LED model, so that you can pull and reverse the
LED model from the mounting hole during any work.
Connect the LED model to the lighting power output of a model
train transformer (e. g. item 5200) or power supply as shown
in fig. 2 and/or 3.
DC voltage: Connect the diode (red part with black marker)
with the plus pole of the power supply, the resistor with the minus
pole.
AC voltage: Operation with AC voltage could cause some flickering.
We recommend to use the Viessmann power module, item 5215,
which is sufficient for approx. 100 LED lamps or reflectors (fig. 3). Con-
nect the cable to the diode with the brown output socket, the resistor
with the red output socket of the power module.
5. Warranty
Each model is tested to its full functionality prior to delivery. The
warranty period is 2 years starting from the date of purchase.
Should a fault occur during this period please contact our service
department (service@viessmann-modell.com). Please send
the item to the Viessmann service department for checking and
repair only after consultation. If we find a material or production
fault to be the cause of the failure, the item will be repaired free
of charge or replaced. Expressively excluded from any warranty
claims and liability are damages of the item and consequential
damages due to inappropriate handling, disregarding the instruc-
tions of this manual, inappropriate use of the model, unauthor-
ized disassembling, construction modifications and use of force,
overheating and similar.
6. Technical data
Operating voltage:
Operating current:
Änderungen vorbehalten. Keine Haftung für Druckfehler und Irrtümer.
Die aktuelle Version der Anleitung finden Sie auf der Viessmann Homepage
unter der Artikelnummer.
Subject to change without prior notice. No liability for mistakes and printing
errors.
You will find the latest version of the manual on the Viessmann website using
the item number.
FR
Cet modéle
se recycle
Points de collecte sur www.quefairedemesdechets.fr
4
(with and without item 5215, power module)
Entsorgen Sie dieses Produkt nicht über den (unsortierten)
Hausmüll, sondern führen Sie es der Wiederverwertung zu.
Do not dispose of this product through (unsorted) domestic
waste, supply it to recycling instead.
À DÉPOSER À DÉPOSER
EN MAGASIN EN DÉCHÈTERIE
OU
Viessmann
Bahnhofstraße 2a
D - 35116 Hatzfeld-Reddighausen
info@viessmann-modell.com
+49 6452 9340-0
www.viessmann-modell.de
13 – 24 V digital signal
Modelltechnik GmbH
10 – 16 V AC ~
14 – 24 V DC =
ca. 10 mA
FR
Made in Europe
Stand 03/sw
03/2023
92369
Ho/Kf