Plantronics DuoPro H151N Quick Start User Manual page 3

H151 Final 9/19/02 9:32 AM Page 2
Use these steps to get set up quickly:
1
2
Earloop for
Over-the-Ear
Configuration
tail adjusts (in and
out and side to side)
for stabilization and fit
I dentify the 3
Cable
Components
Retainer
see blow-up 3.5
1
Headset
Receiver
4
outside Voice Tube
view setup (removable)
for right
ear use
or
5
Noise-Canceling (N)
Microphone Boom
(not removable)
6
Pivot Pin
Cable
1
to the Quick
Headset
Disconnect™
Receiver
connector
inside view
7
Ear Cushion
Foam Pad
5
Examine
the Additional
Features
Clothing Clip
The clothing clip keeps
the headset properly
seated and free from
the cord's weight.
Attach the clothing clip
at a comfortable level.
™
Quick Disconnect
Connector
This feature allows you to
place a call on hold and
move away from the phone
without removing the
headset.
When you separate the
Quick Disconnect, you
place an ongoing
conversation on hold.
Before using your headset,
join the Quick Disconnect to the mating connector of
the modular adapter cable.
To put your call on hold, grasp Quick Disconnect, as
shown, and pull straight apart. To resume your
conversation, reconnect the pieces.
See Maintenance and Troubleshooting section on the other side.
DUOPRO ®
FAMILY OF HEADSETS
10
11
Cable
Headband for
Retainer
Over-the-Head
Configuration
adjustable
12
8 Stabilizer
Bars
Pivot Pin
13
Holder
Pivot Pin Holder reverses
direction for left ear use
16
Cable Retainers
14
Neckband for
Behind-the-Head
Configuration
9
4
4.2
Adjust
the Headset
Over-the-Ear Headset
4.1 To put on the headset, move
earloop away from headset
2
receiver and place earloop over
1
your ear.
4.2 Adjust the flexible earloop (up and
down and side to side) for stabilization
and fit as shown.
Over-the-Head Headset
4.3 Adjust headband length so
11
stabilizer bars rest above your ears.
If necessary, to increase or decrease
tension on your head, bend the metal
part of headband inward or outward
for desired comfort.
Behind-the-Head Headset
Place the assembled neckband so the
headset receiver (See 3.8-3.10) is over
the ear.
4.6 Adjust for comfort.
All Configurations
4.4 Push headset receiver close to
1
your ear until it feels comfortable and
you can hear sound from the
telephone clearly.
4.5 The end of the microphone boom
or voice tube should be placed a
4
distance of two fingers from the
corner of your mouth.
2
*
Configure
the Headset
Assemble the
Headset
15
Removable Tip
3
17
Pivot Pin Holder
For all configurations:
3.1 Begin by disconnecting the headset
from its current right ear configuration.
3.2 Rotate the headset receiver
flipping it to the opposite direction.
The headset rotates only in one direction.
4.1
For noise-canceling
3.3 Pull out the microphone boom
and rotate clockwise to face the
opposite direction.
For voice tube
Rotate the voice tube in the opposite direction.
For Over-the-Ear configurations:
3.4 Position the earloop
4.3
side of headset receiver to fit on left ear.
3.5 Form a small loop in the cable
4.4 positioning flexibility then snap the cable
into the cable retainer
For Over-the-Head configurations:
3.6 Rotate the pivot pin holder
3.7 Form a small loop in the cable
4.5
positioning flexibility then snap the
cable into the cable retainer
For Behind-the-Head configurations:
3.8 Pull off the removable tip
the left side and push it into right side.
4.6
4.6 3.9 Push the pivot pin
holder .
5 17
3.10 Form a small loop in the cable
Adjust
positioning flexibility, snap the cable into the
for comfort.
cable retainers
*
3.7
Assemble the
Headset
Over-the-Head
for right ear use
*
*
Note: May need
to apply pressure when
changing configurations.
Assemble the
Headset
Convert Headset
for Left Ear Use
3.1
clockwise
1
N-models:
5
5
models:
4
on opposite
8
for
9
.
3
as shown.
13
for
9
.
10
from
15
3.8
into the pivot pin
6
3.9
for
9
.
16
3.5
Over-the-Ear
for right ear use
3.10
Behind-the-Head
for right ear use
3.2
3.3
3.5 3.4
3
3.7
3.6
3.10