Advertisement
Quick Links
Advertisement
Related Manuals for Foxconn BCM92046
Summary of Contents for Foxconn BCM92046
- Page 1 BCM92046 Manual...
- Page 2 FCC/IC Warning Statement • Federal Communication Commission Interference Statement • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 FCC/IC Warning Statement for Module • This device is intended only for OEM integrators under the following conditions: • The antenna must be installed such that 20 cm is maintained between the antenna and users, and • The transmitter module may not be co-located with any other transmitter or antenna, •...
- Page 4 NCC 警語 • 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功 能。 • 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發 現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使 用。前項合法通信，指依電信法規定作業之無線電通信。低功率 射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機 設備之干擾。 • 本模組於取得認證後將依規定於模組本體標示審合格籤，並要求 平台上標示「本產品內含射頻模組：ID編號」...
- Page 5 Product Specification Items Contents Bluetooth standard BT V2.1+EDR FHSS, GFSK, π/4-DQPSK,8DPSK Modulation type Channel for USA ,Europe and most other countries as below: Number of channels f=2402+k MHz ,k=0,1,2,3…..,78 Carrier frequency of each channel f=2402+k MHz ,k=0,1,2,3…..,78 Maximum output power to Antenna, power control value Bluetooth: 1.09dBm 3.3V+/-5% Power Rating (DC/AC, Volt rating)
- Page 6 To execute ActivePerl...
- Page 7 select it...
- Page 8 Select it Click it...
- Page 9 select it...
- Page 10 select it...
- Page 11 Select it...
- Page 12 Select it...
- Page 15 1.To execute BlueToolInstall (Version:V.0.8.7.2) Execute below BluetoolInstall Click it...
- Page 16 Choice that. Click it.
- Page 17 Click it.
- Page 18 Click it.
- Page 19 Click it...
- Page 20 Click it...
- Page 21 2. Driver in BTWUSB After inserting the bluetooth module, it will search driver of BTWUSB as below.
- Page 22 Then Select the Driver location and press “Next”...
- Page 25 3.How to use Bluetool • Open Log window...
- Page 27 Click HCI control in Transport to launch Bluetooth Module Select HCI control...
- Page 28 Select USB 0...
- Page 29 Choose 0-Vendor-specific Commands(0 key)
- Page 30 Click Set_TX_Carrier_Frequency_2045 for Transmitter Testing...
- Page 31 Select frequency Select Carrier on Select Modulation Type Select Mode Select TX_Power_Level (We select 0dBm)
- Page 32 Click Write_Receive_Only for Receiving Testing...
- Page 33 Select Frequency...
Need help?
Do you have a question about the BCM92046 and is the answer not in the manual?
Questions and answers