Advertisement
——Assembly and Safe Use Manual ——
BNF0701B / BNF1501B / BNF2101B
7 1/2', 15', 21' Fixed Player Bench
P A R T S L I S T
Item
7 1/2'
15'
21'
Qty
Qty
Qty
A
2
4
4
B
0
0
2
C
2
3
4
D
8
12
16
E
8
12
16
F
8
8
8
G
4
6
8
H
4
4
4
Note: Extra hardware may be included
Inspect all contents prior to installation. Report any missing parts to dealer immediately.
Read all instructions before proceeding.
1.
15' and 21' seat and foot planks are shipped in multiple sections.
15' planks consist of two 7 1/2' Aluminum Seat Planks (A). 21'
planks consist of one 6' Aluminum Seat Plank (B) in the middle
with one 7 1/2' Aluminum Seat Plank (A) on each end.
2.
Plank sections are connected using Seat Connector Tubes (L), Seat
Connector Caps (I), #14 X 3/4" Self Drilling/Threading Hex
Screws (M) and 3/8" Hex Magnetic Screw Drive Socket (N).
3.
Insert two Seat Connector Tubes (L) approximately 5" into the end
of each plank that will be attached to an adjoining plank. Using
3/8" Hex Magnetic Screw Drive Socket (N) and a cordless or
electric drill install two #14 X 3/4" Self Drilling/Threading Hex
Screws (M) through the plank and into each
Seat Connector Tube (L) located approximately as shown.
See Figure 1.
4.
Slide two Seat Connector Caps (I) back to back over the Seat
Connector Tubes (L). See Figure 2.
NOTE: These two Seat Connector Caps (I) may be replaced in the
future by a single double-sided Seat Connector Cap (I)
5.
Position, then adjust plank tightly against the mating plank and
install two #14 X 3/4" Self Drilling/Threading Hex Screws (M)
through the mating plank and into each Seat Connector Tube (L)
See Figure 3.
6.
Repeat this process at each multi-section plank assembly location.
Implementation Date: 10/27/22
Description
7 1/2' Aluminum Seat Plank
6' Aluminum Seat Plank
Leg Assembly
3/8-16 x 3" Carriage Bolt
3/8" Lock Washer
Bench Clamp
Plastic Tube Plug
Seat End Cap
Rev: 9
NJC
Item
7 1/2'
15'
21'
Qty
Qty
Qty
I
0
4
8
J
8
8
8
K
8
12
16
L
0
4
8
M
0
16
32
N
0
1
1
O
TBD
TBD TBD Premix Concrete
File: BNFBA
1
Customer Service
(800) 247-7668
Description
Seat Connector Cap
#10 X 3/4" Sheet Metal Screw
3/8" Hex Nut
Seat Connector Tube
#14 X 3/4" Self Drilling/Threading Hex Screw
3/8" Hex Magnetic Screw Drive Socket
Figure 3
Ref#: 990014
Figure 1
Figure 2
JED
Advertisement
Table of Contents
Related Manuals for Bison BNF0701B
Summary of Contents for Bison BNF0701B
- Page 1 ——Assembly and Safe Use Manual —— BNF0701B / BNF1501B / BNF2101B 7 1/2’, 15’, 21’ Fixed Player Bench Customer Service (800) 247-7668 P A R T S L I S T Item 7 1/2’ 15’ 21’ Description Item 7 1/2’...
- Page 2 Attach Leg Assembly (C) to the seat plank assemblies from above using 3/8” X 3” Carriage Bolts (D), 3/8” Lock Washers (E), 3/8” Hex Nuts (K) and Bench Clamps (F). Use Seat Connector Tubes (L) on the center legs in place of Bench Clamps (F). Legs should be spaced 71” center to center with equal plank lengths extending beyond the legs on 7 1/2’...
Need help?
Do you have a question about the BNF0701B and is the answer not in the manual?
Questions and answers