Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datcon DT1102 (PS)
Summary of Contents for Datcon DT1102 (PS)
- Page 1 DT1102 (PS) Switch Configurable I/O Galvanic Isolator Operating Instructions...
-
Page 2: Table Of Contents
DT1102 (PS) Contents . About this document..............4 1.1. Function....................4 1.2. Target group..................4 1.3. Symbolism used .................. 4 2. For your safety................5 2.1. Authorized personnel................5 2.2. Appropriate use ................... 5 2.3. Warning about misuse ................. 5 2.4. General safety instructions ..............5 2.5. - Page 3 DT1102 (PS) 6. First „power on”, front panel indicators ......20 6.1. First „power on” ................. 20 6.2. Front panel Indicators................ 20 7. Fault rectification..............21 7.1. Fault finding..................21 7.2. Repearing..................21 Dismounting................22 8.1. Dismounting procedure..............22 8.2. Disposal..................... 22 9. Appendix ................23 9.1.
-
Page 4: About This Document
DT1102 (PS) start 1. About this document 1.1. Function This operating instructions manual has all the information you need for quick set-up and safe operation of DT1102 (PS) Please read this manual before you start setup. 1.2. Target group This operating instructions manual is directed to trained personnel. The contents of this manual should be made available to these personnel and put into practice by them. -
Page 5: For Your Safety
For safety and warranty reasons, any internal work on the instruments must be carried out only by DATCON personnel. 2.2. Appropriate use The DT1102 (PS) is an instrument for industrial use. Detailed information on the application range is available in chapter 3. -
Page 6: Product Description
DT1102 (PS) 3. Product description 3.1. Delivery configuration The scope of delivery encompasses: Delivered items • DT1102 (PS) • tool for switch setting (in case of shipping more instrument only one tool is enclosed) • documentation: this operating instructions manual certification warranty 3.2. -
Page 7: Operating Principle
DT1102 (PS) 3.3. Operating principle The DT1102 (PS) Switch Configurable I/O Galvanic Isolator Area of application provide signal transmission and conversion between transmitters and signal processing units. The instruments feature complete 3-way isolation: the input, the output and the power supply are isolated from each other. The instrument has two inputs: 1. -
Page 8: Indicators, Configuration Switches
DT1102 (PS) 3.4. Indicators, configuration switches The following figure shows the indicators and the configuration switches on the DT1102 (PS) front panel. (1) configuration switches for selection input/output ranges (2) red „error” indicator shows the error states (3) green „on” indicator shows the power on state 20220202-V0... -
Page 9: Input/Output Signal Selection
DT1102 (PS) 3.5. Input/output signal selection Four different input/output signal range can be selected with the front panel switches: 0-20 mA, 4-20 mA, 0-10 V, 2-10 V Default setting: 0-20 mA input, 0-20 mA output (all switches are in „off” state). The following figure shows the input/output signal range selection table: The following figure shows steps of setting:... -
Page 10: Storage And Transport
DT1102 (PS) 3. Set the configuration switches according to the signal range selection table 4. Close the front panel cover Do not use other tool than the enclosed one because you may cause injury either to switches or to front panel! 3.6. -
Page 11: Mounting
DT1102 (PS) 4. Mounting 4.1. General instructions The instrument should be installed in a cabinet with sufficient IP protection, where the operating conditions are in accordance with chapter 9.1. Technical specification, as described under the title: Operating conditions. The DT1102 (PS) is built in a plastic housing, for mounting on TS-35 Mounting position rail. -
Page 12: Mounting Procedure
DT1102 (PS) 4.3. Mounting procedure The following figure shows the mounting procedures (fixing on the rail): Mounting on the rail The mounting doesn’t need any tool. 1. Tilt the instrument according to the figure; put the instrument’s mounting hole onto the upper edge of the rail (figure step 1.). 2. -
Page 13: Connecting
DT1102 (PS) 5. Connecting 5.1. Preparing the connection Always observe the following safety instructions: • The connection must be carried out by trained and authorized personnel only! • Connect or disconnect only in the complete absence of line voltage • You should take note the data concerning on the overcurrent protection in installation. -
Page 14: Connecting Active Output Current Source To The Input
DT1102 (PS) 5.2. Connecting active output current source to the input The following figure shows connecting active output current source to the input: Wiring plan, connecting active output current source (see also “Application example”) Be careful the polarity of the cables 1. -
Page 15: Connecting 4-20 Ma Two Wire (Passive) Transmitter To The Input
DT1102 (PS) 5.3. Connecting 4-20 mA two wire (passive) transmitter to the input The following figure shows connecting 4-20 mA two wire (passive) transmitter to the input: Wiring plan, connecting 4-20 mA two wire transmitter (see also “Application example”) Be careful the polarity of the cables 1. -
Page 16: Connecting Voltage Source To The Input
DT1102 (PS) 5.4. Connecting voltage source to the input The following figure shows connecting voltage source to the input: Wiring plan, connecting voltage source (see also “Application example”) Be careful the polarity of the cables 1. Loosen terminal screws. 2. Insert the wire ends into the open terminals according to the wiring plan. -
Page 17: Connecting Current Output To The Signal Processing Unit
DT1102 (PS) 5.5. Connecting current output to the signal processing unit The following figure shows connecting current output to the signal processing unit: Wiring plan, connecting current output (see also “Application example”) Be careful the polarity of the cables 1. Loosen terminal screws. 2. -
Page 18: Connecting Voltage Output To The Signal Processing Unit
DT1102 (PS) 5.6. Connecting voltage output to the signal processing unit The following figure shows connecting current output to the signal processing unit: Wiring plan, connecting voltage output (see also “Application example”) Be careful the polarity of the cables 1. Loosen terminal screws. 2. -
Page 19: Connecting Instrument To The Power Supply
DT1102 (PS) 5.7. Connecting instrument to the power supply The following figure shows connecting the instrument to the power supply: Wiring plan, connecting the power supply (see also “Application example”) The polarity of the cables is indifferent 1. Before connecting check that the supply voltage correspond with the supply voltage written on the data label. -
Page 20: First „Power On", Front Panel Indicators
DT1102 (PS) 6. First „power on”, front panel indicators 6.1. First „power on” After you have completed the connections, put the instrument under supply voltage. If the connection is correct green “on” indicator lights, red “error” indicator dark and you can measure the expected current or voltage on the output. -
Page 21: Fault Rectification
7.2. Repearing There is no user repairable part inside the instrument. In accordance with Point 2.1.: For safety and warranty reasons, any internal work on the instrument must be carried out only by DATCON personnel. 20220202-V0... -
Page 22: Dismounting
DT1102 (PS) 8. Dismounting 8.1. Dismounting procedure Before dismounting take note the warnings written in chapter 5.1. Preparing the connection. The following figure shows the dismounting procedures. Dismounting from the rail The dismounting procedure needs a screwdriver for slotted screws. Before dismounting disconnect all wires. -
Page 23: Appendix
DT1102 (PS) 9. Appendix 9.1. Technical specification Input parameters (current) Input signal: DC current Ranges: 0-20 mA, 4-20 mA Overload: 400 mA Input resistance: 10 Ω Input parameters (voltage) Input signal: DC voltage Ranges: 0-10 V, 2-10 V Overload: 100 V Input resistance: 102 kΩ... - Page 24 DT1102 (PS) Power supply Supply voltage: DT1102 24 VDC ±10%, 1.6 W DT1102 PS 230 V AC/DC ±10%, 3.8 VA (2.4 W) Overvoltage class: CAT II. The overcurrent protection in installation: 4 A (B) Ambient conditions Operating temperature range: 0-50 °C * Storage temperature range: -20 - +70 °C Relative humidity:...
-
Page 25: Application Example
DT1102 (PS) start 9.2. Application example 20220202-V0... - Page 26 DT1102 (PS) 20220202-V0...
- Page 27 DT1102 (PS) 20220202-V0...