Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MyBinding Baum 714XLT
Summary of Contents for MyBinding Baum 714XLT
- Page 1 Baum 714XLT Ultrafold Air Feed Tabletop Paper Folder Instruction Manual...
- Page 2 BAUMFOLDER CORPORATION Quality Bindery Equipment Since 1917 714XLT AIR FEED FOLDER INSTALLATION, OPERATION, MAINTENANCE & PARTS MANUAL © Baumfolder Corp., 2006 Printed in U.S.A. TP10289-3 PAGE 1 TP10289-3...
- Page 3 © 2006 All Rights Reserved WARNING • Do not operate this machine without all guarding in place. • Do not make adjustments or perform maintenance on this machine with power on. • Keep the machine and the work area clean and free of spills to prevent accidents. •...
-
Page 4: Table Of Contents
Contents 1.0 INTRODUCTION ..............................4 2.0 SPECIFICATIONS ..............................4 3.0 INSTALLATION ............................... 4 3.1 Unpacking & Inspection ............................. 4 4.0 ASSEMBLY ................................5 4.1 Main Unit ..................................5 4.2 Pump Electrical Connections ............................5 4.3 Pump Hose Connections ............................. 5 4.4 Slitter Shaft Installation ............................... -
Page 5: Introduction
1.0 INTRODUCTION Your new 714XLT Air Feed Table Top Folder has been designed to give you many years of useful service provided it is installed, maintained, and operated according to the instructions in this manual. Your 714XLT Air Feed is a unique and versatile paper folding machine, capable of folding paper measuring between 3 x 5 inches (7.6 x 12.7 cm) and 14 x 20 inches (35.5 x 50.8 cm), at speeds up to 35,000 sheets per hour of 8 1/2 x 11 (21.6 x 27.9 cm) and up to 65,000 sheets per hour of 3x5 (7.6x12.7 cm). -
Page 6: Assembly
WARNING 4.3 Pump Hose Connections Do not plug the power cord into an AC outlet until Two hoses come with your 714XLT Air the 714XLT Air Feed is fully assembled, adjusted and Feed. (See Figure 4.3-1) ready to use. Unplug the 714XLT any time disassembly is required. -
Page 7: Delivery Table
4.5 Delivery Table Feed Table Hoses To install the delivery table, loosen the knobs on either side of the stacker table. Drop the tray over the knobs and retighten. Vacuum Pump Hoses Figure Figure 4.6-2 4.5-1 4.6 Feed Table Assembly Installation Insert the feed table with the feed wheel toward the fold rolls. -
Page 8: Fold Plate Installation
5.0 ELECTRICAL ACCESS 4.7 Fold Plate Installation WARNING WARNING Unplug the AC power cord before attempting any electrical repair. Unplug the AC power cord when installing or removing fold plates. The motor speed control and counter control are located under the left-hand side cover. The handwheel The fold plates are marked #1 and #2 and are not must be removed for access to these controls. -
Page 9: Paper Stop Adjustment
Figure 6.2-1 D) Locate the point on the chart where the columns for the type of fold and the sheet size intersect. You will notice that there are either two letters or a dash and a letter. These letters and/or dash tell you where to set the paper stop on the fold plate, and whether or not one of the fold plates will be installed in the deflector position. -
Page 10: Feed Table Adjustment
6.6 Air Blow Adjustment 6.5 Feed Table Adjustment Turn the air blow adjustment on the vacuum/aircontrol On the paper feed table there are two guides which panel fully counterclockwise to the + position. Except for keep the stack of paper properly aligned for feeding into when very small sheets are being run, the air blow the folder. -
Page 11: Check Squareness Of Fold
TOP SHAFT Additional paper can be loaded on top of the stack of paper already in the feeder without stopping the machine. If the feeder runs out of paper or if you want to stop the machine for any reason, first turn off the vacuum pump, then the folder. -
Page 12: Scoring
TOP SHAFT 8.2 Scoring The 714XLT can be used to score a sheet and deliver it flat, or to score a sheet after a fold or folds have been made. To ensure accuracy in making right-angle folds, always score the sheet where the fold is to be made. This applies in all instances when a perforator cannot be used. -
Page 13: Maintenance
Before tightening the blade to the collar, slide the blade with the collar loosely attached on the end of the 9.6 Cleaning The Fold Stop Guides shaft. Then tighten securely, thus aligning both the blade and collar, allowing free horizontal movement along the The fold stop guides (See figure 4.7-1) should be... -
Page 14: Material Safety Data Sheet
irritation and may affect central nervous system. May cause SUREWASH skin irritation. Chronic over-exposure to many petroleum 10.0 MATERIAL SAFETY DATA hydrocarbons may cause liver or kidney injury. May cause SHEET eye irritation. NOTICE: Surewash is a product of RBP Chemical Emergency &...
Need help?
Do you have a question about the Baum 714XLT and is the answer not in the manual?
Questions and answers