Related Manuals for cam SHP Series
Summary of Contents for cam SHP Series
- Page 1 Original operating manual Operating manual SHP sideshifter SHP-series Flexibility & experience 04/2022 – V01...
- Page 2 © 04-2022. CAM attachments is a trademark of TVH Parts Holding NV, Brabantstraat 15, B-8790 Waregem. All rights reserved. No part of this publication may be reproduced or communicated in any form or by any means, electronic or mechanical, including copying, recording or use in an information storage or retrieval system, without prior and explicit permission of TVH Parts Holding NV.
- Page 3 Bulgarian Можете да намерите това ръководство на Вашия език чрез линка, посочен по – долу. Czech Tento návod najdete ve svém jazyce prostřednictvím odkazu níže. Danish Du kan finde denne vejledning på dit sprog via nedenstående link. German Sie finden diese Bedienungsanleitung in Ihrer Sprache unter folgendem Link. Greek Μπορείτε...
- Page 4 Thank you for using our product. For your safety and to ensure a correct operation, we would like to bring to your attention some aspects of this manual: • This booklet supplies useful instructions for the correct operation and maintenance of the product. It is therefore necessary to pay the utmost attention to all of the paragraphs that illustrate the most simple and secure way to operate and use this product.
-
Page 5: Table Of Contents
CONTENTS INTRODUCTION ..................... DESCRIPTION . -
Page 6: Introduction
INTRODUCTION This manual contains all the necessary information on the installation and operation of the SHP sideshifter. Some of the maintenance operations should only be carried out by professional technicians. If you require this information and the maintenance steps, please contact your dealer. Also included in this manual are a number of safety instructions to create a safe working environment. -
Page 7: Description
DESCRIPTION 2.1. Technical data Always check the type plate for the correct information. Model Capacity Weight ISO2328 kg/mm Sideshifters ISO/FEM 2 with sliding pads SHP225.080P.CD1 2500/500 SHP225.090P.CD1 2500/500 SHP225.092P.CD1 2500/500 SHP225.094P.CD1 2500/500 SHP225.098P.CD1 2500/500 SHP225.100P.CD1 2500/500 1000 SHP225.102P.CD1 2500/500 1020 SHP225.104P.CD1 2500/500 1040... -
Page 8: Operating Pressure And Oil Flow Rate
2.2. Operating pressure and oil flow rate Model Operating pressure Oil flow rate Hydraulic functions Minimum Recommended Maximum Minimum Recommended Maximum l/min l/min l/min SHP225 SHP335 A flow rate less than recommended will result in a lower rotating speed. A flow rate greater than the maximum can result in excessive heating, reduced system performance and reduced hydraulic system life. -
Page 9: Placement Of The Decals
3. Important: Risk of limb crushing 4. Important: Pressurised liquids Cylinder with 166TA5960 plunger rods. Danger: Pressure supply only after complete sideshifter assembly CAM attachments Contact logo your dealer 9/36... -
Page 10: Type Plate
DO NOT EXCEED THE LIFT TRUCK RESIDUAL CAPACITY • DE RESTCAPACITEIT VAN DE HEFTRUCK MAG NIET OVERSCHREDEN WORDEN • DIE RESTKAPAZITAT DES GABELSTAPLERS DARF NICHT UBERSCHRITTEN WERDEN • NE PAS DEPASSER LA CAPACITE RESIDUELLE DU CHARIOT ELEVATEUR • NO EXCEDER LA CAPACIDAD RESIDUAL DE LA CARRETILLA ELEVADORA • NON SUPERARE LA PORTATA RESIDUA DEL CARRELLO ELEVATORE N° Explanation CAM attachments logo Equipment capacity Equipment name... -
Page 11: Safety Instructions
SAFETY INSTRUCTIONS 3.1. Explanation of the safety decals If the decals are damaged or missing, please replace them. Make sure that all the safety messages are legible. Replace damaged stickers asking the manufacturer for new ones. If the part to be replaced bears a sticker, ensure that a new sticker is applied to the new part. Decal Explanation Reference... - Page 12 In the event that equipment, procedures, work methods or working techniques are used that are not specifically advised by the CAM attachments company, it is necessary to make sure that there is no danger to the operator or other people.
-
Page 13: Transport And Storage
TRANSPORT AND STORAGE 1. Transport If you want to transport the sideshifter on a pallet, make sure that the attachment is securely attached so it can’t fall off. Safely transport the sideshifter by following the next steps: 1. Check the type plate to know the weight of the sideshifter. Select the appropriate material according to the weight (ropes, cables, hooks, etc.) 2. -
Page 14: Assembly And Installation
• The assembly and installation must be carried out by an expert. • Make sure that the goods and packaging are in good condition. • Before commissioning, carry out a risk analysis on the assembly of the CAM attachment with the forklift. - Page 15 3. Release the sliding pads. Before lifting the equipment, make sure that the lifting device (ropes, cables, hooks, etc) are adequate for the weight of the equipment (see identification label). Check the stability of the equipment before lifting. 4. Strap and lift the sideshifter as indicated in the figure. The minimum capacity of the lifting device must be 200 kg.
- Page 16 5. Place the sideshifter parallel to the fork carriage of your lifting device. 6. Insert the sideshifter locking tab (A) in the seat (B) on the truck’s fork carriage. Centre the sideshifter on the fork carriage. 7. Lift the sideshifter together with the fork carriage and set the two bottom hooks, securing them with their bolts and their plates.
- Page 17 8. Connect the two oil lines (B). 9. Unscrew and remove the safety screw (C). 10. Lift and insert the first fork in the sideshifter central zone (D) and shift it to the left. Insert the second fork and shift it to the right. Centre the two forks on the sideshifter.
- Page 18 After the assembly of the attachment and before putting the device into operation, check if all the functions operate correctly. Any failure of the safety devices can cause malfunctioning and damage to the attachment. 5.3.1. Bleeding the hydraulic system before use To prevent air from entering your hydraulic system, which could eventually cause damage to the sideshifter, it’s necessary to bleed the hydraulic system before use.
-
Page 19: Operation
• In the event of non-envisaged workmanship or intervention, or following a procedure different to that indicated in the manual, consult CAM attachments before proceeding in order to ascertain its feasibility. • Never stand or work under the sideshifter to prevent third parties from being hit by falling objects during work. -
Page 20: Operating Instructions
6.2. Operating instructions Perform the daily maintenance check before each use as described in chapter ‘7.3. Maintenance instructions’ . 6.2.1. Load lifting Before starting First, use the hydraulic levers to check which levers operate which function. Use all the functions several times with no load to check if they function normally and smoothly. Before lifting a load, operate the forks several times in order to remove air from the circuit. - Page 21 6.2.2. Load handling Don’t drive with a non-centred load (shifted towards the left or right). Make sure that loads can’t move freely, they may fall and cause accidents. 1. Set the forks of your lifting device in the correct position and as wide as possible for the load to be carried.
-
Page 22: Maintenance
MAINTENANCE 7.1. Safety instructions for the maintenance of the product • For maintenance, place the sideshifter in its lowest position to the ground. Switch off the vehicle’s engine and remove the key. • Use tools and equipment suited to the work to be undertaken. •... -
Page 23: Maintenance Instructions
Maintenance instructions In the event of problems or if operations are to be undertaken that are not specifically described in this manual, consult CAM attachments or the retailer. 1. Daily maintenance check A daily check of the sideshifter can limit wear to a minimum: •... - Page 24 Never try to seal a leak yourself. This can cause injuries or damage to your skin and clothes. Only qualified and authorised personnel is permitted to repair or maintain the product. To prevent leaks, replace hydraulic hoses if needed while wearing safety gloves. May only be done by a qualified service technician and according to the manufacturer’s instructions.
- Page 25 7. Check the wear of the packing seals Check the wear of the packing seals and replace them if necessary. May only be done by a qualified service technician and according to the manufacturer’s instructions. 8. Check the hydraulic oil In case of dirt in the hydraulic system, it is necessary to change the oil completely.
-
Page 26: Troubleshooting
TROUBLESHOOTING N° Problem Cause Action Impossible to Oil leak Check the connections. sideshift the load Replace or repair the pump/valve Replace the seals Air in the hydraulic system Bleed the air from the system, run the cylinders through several lift cycles. See chapter 5.3.1. -
Page 27: Final Decommissioning And Disposal
FINAL DECOMMISSIONING AND DISPOSAL Final, proper decommissioning or disposal of the product must be performed in accordance with the regulations of the country in which the product is used. In particular, regulations governing the disposal of batteries, fuels and electronic and electrical systems must be observed. Waste packaging should be sorted and put into solid dustbins according to the materials and needs to be collected by the local special environmental protection bureau. -
Page 28: Annexes
ANNEXES 10.1. CE certificate 28/36... - Page 29 29/36...
-
Page 30: 10.2. Hydraulic Diagram
10.2. Hydraulic diagram If you request a detailed hydraulic diagram, please contact the manufacturer. 30/36... -
Page 31: 10.3. Spare Parts List
10.3. Spare parts list Sideshifter SHP225 N° Description Note Upper slide plate 165TA7202 Anchor bracket l-645 165TA7206 For SSP L-800 Anchor bracket l-690 165TA7207 For SS from L-900 to L-980 Anchor bracket l-790 165TA7208 For SS from L-1000 to L-1070 Anchor bracket l-890 165TA7209 For SS from L-1100 to L-1150... - Page 32 Sideshifter SHP335 N° Description Note Upper slide plate 165TA7204 Anchor bracket L-790 165TA7212 For SS from L-1000 to L-1070 Anchor bracket L-890 165TA7213 For SS from L-1100 to L-1150 Anchor bracket L-990 165TA7214 For SS from L-1200 to L-1250 Anchor bracket L-1090 165TA7215 For SS from L-1300 to L-1350 Anchor bracket L-1190...
- Page 33 NOTES ................................
- Page 34 NOTES ................................
- Page 35 NOTES ................................
- Page 36 Your distributor: Manufactured outside the EU for TVH PARTS HOLDING NV. www.camattachments.com Agri info@camattachments.com Construction Industry Brabantstraat 15 Food & 8790 Waregem beverage Belgium Paper T +32 56 43 42 11 handling F +32 56 43 44 88...