Related Manuals for cam HS Series
Summary of Contents for cam HS Series
- Page 1 Original operating manual Operating manual Hydraulic scoop fork-mounted HS-series Flexibility & experience 03/2022 – V01...
- Page 2 BH24468 © 03-2022. CAM attachments is a trademark of TVH Parts Holding NV, Brabantstraat 15, B-8790 Waregem. All rights reserved. No part of this publication may be reproduced or communicated in any form or by any means, electronic or mechanical, including copying, recording or use in an information storage or retrieval system, without prior and explicit permission of TVH Parts Holding NV.
- Page 3 Bulgarian Можете да намерите това ръководство на Вашия език чрез линка, посочен по – долу. Czech Tento návod najdete ve svém jazyce prostřednictvím odkazu níže. Danish Du kan finde denne vejledning på dit sprog via nedenstående link. German Sie finden diese Bedienungsanleitung in Ihrer Sprache unter folgendem Link. Greek Μπορείτε...
- Page 4 Thank you for using our product. For your safety and to ensure correct operation, we would like to bring to your attention some aspects of this manual: • This booklet supplies useful instructions for the correct operation and maintenance of the product. It is therefore necessary to pay the utmost attention to all of the paragraphs that illustrate the most simple and secure way to operate and use this product.
-
Page 5: Table Of Contents
CONTENTS INTRODUCTION ..................... DESCRIPTION . -
Page 6: Introduction
INTRODUCTION This manual contains all the necessary information on the installation and operation of the hydraulic scoop. Some of the maintenance operations should only be carried out by professional technicians. If you require this information and the maintenance steps, please contact your dealer. Also included in this manual are a number of safety instructions to create a safe working environment. -
Page 7: Description
DESCRIPTION 2.1. Technical data Always check the type plate for the correct information. Model Volume Height Width Length Max fork Min distance Weight (H2) (B1) (L3) section between forks BH24466 1640 1394 185 X 70 BH24468 1100 1840 1394 185 X 70 2.2. -
Page 8: Placement Of The Decals
2.4. Type plate N° Explanation Manufactured outside the EU for: TVH PARTS HOLDING NV Address Brabantstraat 15 • 8790 Waregem • Belgium CE logo CAM attachments logo TYPE Type MODEL Model MODÈLE MODEL MODELL SERIENR. Serial number °... -
Page 9: Safety Instructions
In the event that equipment, procedures, work methods or working techniques are used that are not specifically advised by the CAM attachments company, it is necessary to make sure that there is no danger to the operator or other people. -
Page 10: Transport And Storage
TRANSPORT AND STORAGE 1. Storage The hydraulic scoop must always be stored in a dry, frost-free and temperature-controlled environment. Do not store this product outside in a wet environment. Store the hydraulic scoop in a safe place and make sure it can’t fall over. Lubricate metal parts with an anti-corrosive agent (REF 166TA1570 or REF 143TA6901). -
Page 11: Assembly And Installation
• The assembly and installation must be carried out by an expert. • Make sure that the goods and packaging are in good condition. • Before commissioning, carry out a risk analysis on the assembly of the CAM attachment with the forklift. - Page 12 3. Make sure the scoop is located on a flat surface centrally in front of the vehicle in its horizontal position (do not tilt the hydraulic scoop during the installation). 4. Secure the hydraulic scoop onto the forks with the provided screws on the fork pockets. Make sure the hydraulic scoop cannot slip from the forks.
-
Page 13: Operation
• For safety reasons, arbitrary adaptations or modifications to the equipment are prohibited. • In the event of non-envisaged workmanship or intervention or following a procedure different to that indicated in the manual, consult CAM attachments before proceeding in order to ascertain its feasibility. -
Page 14: Operating Instructions
• In the event of injury caused by oil escaping under pressure, immediately seek medical assistance. 6.2. Operating instructions Please see chapter 7 for the daily maintenance schedule. Perform the daily maintenance check before each use as described in chapter ‘7.3. Maintenance instructions’... - Page 15 6. Provide sufficient space between the scoop and the ground if you want to tilt the scoop into another position. 7. To unload, firstly bring the upright to a vertical position and then slowly lower the forks. 15/28...
-
Page 16: Maintenance
MAINTENANCE 7.1. Safety instructions for the maintenance of the product • For maintenance, place the hydraulic scoop in its lowest position to the ground. Switch off the vehicle’s engine and remove the key. • Before maintaining the hydraulic scoop, carefully read the instructions in the manual of your lifting device. - Page 17 2. Cleaning Only clean the equipment with a cloth dampened in a soap solution (REF 131TA5500)* or TotalSource wipes (REF 147TA3378). Do not use solvents, petrol, strong detergents etc. If the equipment is heavily soiled, the use of a pressure cleaner is only permitted providing that it is set to a maximum of 200 bar.
- Page 18 5. Check the bolts/screws Check that all the screws are properly tightened. In case of damage or loose bolts/screws, replace/tighten the Tighten any screws/bolts if they come loose. Can be done by the user. 6. Regularly check the hydraulic circuit for any leaks Check the hydraulic circuit for any leaks.
-
Page 19: Troubleshooting
TROUBLESHOOTING N° Problem Cause Action Damage to the Frequent use The blade must be replaced by a qualified blade mechanic Malfunction of the Oil leak Check the connections. hydraulic cylinder Replace or repair the pump/valve Replace the seals Air in the hydraulic system Bleed the air from the system, run the cylinders through several lift cycles. -
Page 20: Final Decommissioning And Disposal
FINAL DECOMMISSIONING AND DISPOSAL Final, proper decommissioning or disposal of the product must be performed in accordance with the regulations of the country in which the product is used. In particular, regulations governing the disposal of batteries, fuels and electronic and electrical systems must be observed. Waste packaging should be sorted and put into solid dustbins according to the materials and be collected by the local special environmental protection bureau. -
Page 21: Annexes
ANNEXES 10.1. CE certificate 21/28... - Page 22 22/28...
-
Page 23: 10.2. Hydraulic Diagram
10.2. Hydraulic diagram If you request a detailed hydraulic diagram, please contact the manufacturer. 23/28... -
Page 24: 10.3. Spare Parts List
10.3. Spare parts list REF BH24466 REF BH24468 24/28... - Page 25 Nr Description Connecting device* 167TA2155 1A Connecting hook 167TA2156 1B Bolt 167TA2157 1C Screw 122TA9039 1D Nut 107TA6476 1E Security pin 106TA6984 1F Connecting device – welded part 167TA2158 Screw 167TA2162 159TA1018 107TA6520 Screw 122TA9039 Fixing handle 167TA2159 Grease nipple 107TA5528 Fixing plate 167TA2160...
- Page 26 NOTES ................................
- Page 27 NOTES ................................
- Page 28 Your distributor: Made outside the EU for TVH PARTS HOLDING NV. www.camattachments.com Agri info@camattachments.com Construction Industry Brabantstraat 15 Food & 8790 Waregem beverage Belgium Paper T +32 56 43 42 11 handling F +32 56 43 44 88...