Advertisement
2.
INTROdUCTION & SPECIFICATIONS
our range of paraffin/kerosene/diesel heaters represents excellent
value. Workshop tried and tested. Proven pump systems handle
paraffin, kerosene or diesel with only minor adjustment of air
compressor. Both models are fitted with heavy-duty pneumatic
wheels and a heavy-duty filler cap.
sealey Advantages
• PARAFFIN, KEROSENE OR DIESEL - These Sealey AB heaters
will operate on all.
• CLEAN BURNING - A specially designed burner head in a
stainless steel combustion chamber ensures a more thorough
burn of fuel which means greater fuel economy and maximum
heating effect.
• FILTER PROTECTION - The compressor unit is protected by
extra large filter elements.
• LARGE FUEL TANK - These AB series heaters will operate for
between 9 and 11 hours on a single fill of fuel.
• SAFETY FEATURES - The AB series heaters are fitted with a
flame-out device which cuts the fuel supply when the flame is
inadvertently extinguished.
• QUALITY - Manufactured to comply with rigorous standards.
• AFTER SALES SERVICE - The best after sales service in the
business. full spares back up for all models.
Model
rating Btu/hr (kW)
fuel
Fuel Tank Capacity (Litres)
Fuel Consumption (Ltr/hr)
Maximum running time
Pump Pressure (PsI) +/-10%
Voltage/Amp
Air flow (cfm)
3
Heated Area (m
)
Phase
Power cable (m)
size (cm)
net Weight (Kg)
3. ASSEMBLY
unpack the heater and check the contents. should there be
any damaged or missing parts, contact your sealey Dealer
immediately.
3.1.
slide axle through wheel support frame, slide a bushing onto
each end of the axle.
3.2.
Install wheels with valve stem on the outside. thread a domed
nut onto each end of the axle and tighten.
3.3.
Place heater on wheel support frame, ensuring that the air
inlet is by the wheels and line up the holes on the fuel tank
flange with those on the wheel support frame.
3.4.
Place handle on fuel tank flange and line up with the wheel
support frame fixing holes. Insert 2 bolts through the middle
fuel tank flange hole and both frames and secure finger tight
only with nuts and washers.
3.5.
Insert 2 bolts through the fuel tank flange and wheel support
frame and secure finger tight with nuts and washers.
3.6.
Insert 2 bolts through the fuel tank flange and the handle
and secure finger tight with nuts and washers.
3.7.
When assembly is complete, securely tighten all nuts.
WARNING! dO NOT use the heater without the support
frame fully assembled.
AB70E
AB100E
70000 (20.5)
100000 (29.3)
Paraffin/
Paraffin/
Kerosene/Diesel
Kerosene/Diesel
19
38
2.0
3.5
9
11
3.7
4.5
230V/5A
230V/5A
240
520
385
566
single
single
2.1
2.1
99 x 58.5 x 66
99 x 58.5 x 66
15.3
24.5
Original Language Version
Minimum Clearances from Combustibles
top
sides
front
WARNING! This heater is not suitable for use with Bio-Diesel; use of
Bio-Diesel will damage the filter and seals.
Damage caused by use of Bio-Diesel will not be covered by warranty.
1
Wheel support frame
1
Axle
2
Wheels
1
Handle
2
Axle Bushings
2
Domed nuts
6
frame Bolts
6
frame nuts and Washers
AB100E
1.2m
1.2m
2.4m
Assembly Parts
fig.1
AB70E, AB100E
Issue: 1 - 05/04/12
Advertisement
