Advertisement
Available languages
Available languages
US
Read all instructions before using or installing this product.
Technical data
– Supply voltage:
– Required electrical outlet:
– Max. power consumption:
Prod. No.:
33096 XX1550:
33096 XX2050:
33096 XX2550:
33096 XX3050:
33096 XX3550:
– Degree of protection:
– Ambient conditions:
Operating temperature
Storage temperature
– Luminous color
Mounting dimensions, see page 10.
Modes
The device can be operated in two modes.
Mode 1 (ex works):
Lighting On/Off at the device button (Off
automatically after power returns).
Mode 2:
Lighting On/Off at the external light switch (Off
automatically after power returns).
To change mode, see table under Operation:
Installation, see fi gure 1 onwards on page 11.
Before installation check whether the fastening mate-
rials included are suitable for the anchoring base. The
fastening materials are suitable exclusively for stud walls
with timber constructions or for drywall constructions
with timber wood reinforcement.
• Mark the wall bracket position, see fi gure 1.
• Mount the wall brackets to the wall, see fi gure 2.
• Mount the light mirror fi xation, see fi gure 3.
WARNING - GROUNDING
INSTRUCTIONS
This product must be connected to a grounded me-
tal, permanent wiring system, or an equiment-groun-
ding conductor must be run with the circuit con-
ductors and connected to the equipment-grounding
terminal or lead on the product.
Wiring diagram, see fi gure 4 on page 12.
• Connect the light mirror to the power supply,
see fi gure 5a/5b.
• Remove the adhesive cover from the light mirror
fi xation, see fi gure 6.
120 V AC / 50/60 Hz
15 A / 1800 VA
Width
Weight
Light
19-11/16"
20.06 lb
25-19/32"
24.25 lb
31-1/2"
28.22 lb
39-3/8"
33.73 lb
47-1/4"
39.02 lb
NEMA 1
32° – 113° F
-40° – 158° F
3000 Kelvin
• Hang the light mirror on the wall from above,
see fi gure 7 on page 13.
• Press the light mirror to the light mirror fi xation,
see fi gure 8.
27 W
Operation
30 W
Button functions
33 W
Button
Function
42 W
Light on/off
48 W
• Pressing the button switches the light mirror
on with the selected settings. The white LED
goes off.
• Pressing the button again switches the light
mirror off. The white LED lights up.
To change mode
• Switch off the refl ector.
• Press the button and hold it down for 15
seconds.
- The light comes on again if the mode has
Repeat the procedure described to re-enable
mode 1.
• The white LED can be deactivated.
– Switch on the light mirror.
– Press and hold the button for 15 seconds.
- The lighting gets lighter or darker.
- The lighting switches off briefl y and the
To switch the white LED back on, repeat the
described procedure.
Front and wall lighting
• The front and wall lighting is switched on
by pressing the button when light mirror is
switched on.
• Pressing the button again switches the light
off.
Washbasin lighting
• The washbasin lighting is switched on by
pressing the button when light mirror is
switched on.
• Pressing the button again switches the light
off.
When both lightings are switched off, the light
mirror also switches off.
Dimming the front, wall and washbasin
lighting
• Press the button when the light mirror is
switched on and hold until the desired bright-
ness or the end value has been reached.
The setting is stored and reproduced when
switched on again (only for connection type 1,
see fi gure 4 on page 12).
been changed.
white LED is deactivated.
3
Advertisement
