Table of Contents
Advertisement
Quick Links
Sundara
Inlet Triple Basin
®
Hand Washing System
All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the
date of purchase. Decorative finishes warranted for one year. We will replace at no costs goods that prove defective provided we are
notified in writing of such defect and the goods are returned to us prepaid at Atlanta, GA, with evidence that they have been properly
maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages
whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replacement of the
defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended use and the
purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of merchantabi-
lity is expressly excluded. If the products sold hereunder are "consumer products," the implied warranty of merchantability is limited to
a period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our catalogs and lists
are approximate and are not guaranteed.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov
NOTE: The information in this manual is subject to change at any time without notice. Installations may
be performed at different times of construction by different individuals. For this reason, these instructions
should be left on-site with the facility or maintenance manager.
NOTE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT.
Rev. B | Date: 10/13/22 | C.N. No. 144818 | Prod./Dwg. No. FV664
Patent zurn.com/patents
US 1.855.ONE.ZURN CANADA 1.877.892.5216
ZURN.COM
Z5005.03
Sundara
®
Hand Washing System
Installation, Maintenance,
and Parts Manual
PATENT(S) PENDING
LIMITED WARRANTY
Inlet Triple Basin
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ZURN Sundara Z5005.03
Summary of Contents for ZURN Sundara Z5005.03
- Page 1 For this reason, these instructions should be left on-site with the facility or maintenance manager. NOTE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT. Rev. B | Date: 10/13/22 | C.N. No. 144818 | Prod./Dwg. No. FV664 Patent zurn.com/patents US 1.855.ONE.ZURN CANADA 1.877.892.5216 ZURN.COM...
- Page 2 Specifications: Sundara Inlet triple basin lavatory system manufactured by Zurn Industries. Lavatory shall be mounted at standard height to ® conform with ANSI, UFAS, TAS and ADA Accessibility Standards. Counter and integral basin to be constructed of Sundara ®...
- Page 3 Plumbing and Electrical Rough-Ins Required Tools: Torx Wrench: Socket Wrench: Non-toothed Wrench T10 & T25 5/16” & 3/8” L Brackets Installation 2 [12.7] For ease of installation, lay basin on its top surface on a cushioned surface. Install hanger brackets 1/2 inch from front face of L-bracket as shown.** Use socket wrench to torque the screws (approximately 4-5 complete turns bottom out approximately 5 ft-lbs of torque).
- Page 4 Soap Dispenser Installation Retrofitting Hanger Bracket Installation Wall Stud Plywood 3 1 2 [89] 3 1 2 [89] 4 [99] 3 1 2 [89] 3 1 2 [89] 4 [99] Bolt supplied by 1 [25] Hanger Bracket installer to attach the plywood to 1 [25] wall studs...
- Page 5 Installing Mounting Bracket Installing with Carrier Option • Secure the mounting bracket to the plywood cut-out with supplied washers, bolts and toggle an- chors on the plywood. Z1240-EZR Carrier System Wall Stud Plywood Mounting Bracket Bolt supplied by installer to attach the plywood to Optional Waste wall studs...
- Page 6 P Trap Installation & Water Shroud Installation: Supply Connection to Faucet Step 2 Connect the tail piece to Grid Drain (threaded connection) Then attach P-Trap to tailpiece • Remove the wall bracket and drill 3/4” holes into the center of the holes previously marked. Ensure that wall studs are not immediately behind the marked hole locations prior to drilling.
- Page 7 Repair Instructions: • Zurn recommends that damages should be repaired by certified solid surface fabricator or repair agents. • Blemishes to the basin surface (such as scratches, burn marks, and minor chipping) can be repaired by sanding with super-fine(800 or 1000 grit) sand paper and/or maroon Scotch-Brite™...
Need help?
Do you have a question about the Sundara Z5005.03 and is the answer not in the manual?
Questions and answers