Related Manuals for Work Pro LW 465 R
Summary of Contents for Work Pro LW 465 R
- Page 1 PRO LIFTING TOWERS Using & Installation user manual LW 465 R LW 480 R WT 600 Rev. 12.5.6...
- Page 2 LW 465R/480R/WT 600 LIFTING TOWERS INSTALLATION AND USER MANUAL LW 465 R LW 480 R WT 600...
-
Page 3: Table Of Contents
LW 465R/480R/WT 600 LIFTING TOWERS INSTALLATION AND USER MANUAL INTRODUCTION FEATURES SPECIFICATIONS FASTENER SYSTEM (explanation) SAFETY RULES INSTALLING THE LIFTING TOWER PLACING THE LOAD WINCH OPERATION (Special care) LIFTING PROCESS DESCENT/FOLDING PROCESS CONFORMITY DECLARATION BGV C1, EXPLANATION & TEST... -
Page 4: Introduction
6,5 m (LW 465 R), without any effort for the user. These towers have a different number of load, getting a better balance with the coupled load. -
Page 5: Specifications
BASE WEIGHT FASTENER SYSTEM (explanation) (KG) (KG) (KG) STANDARDS AND REGULATIONS MODEL LW 465 R 2,30 x 2,00 2,20 0,70 x 0,60 LW 465 R DIN 15020 / VGB 1 / VGB 8 LW 480 R 2,30 x 2,00 2,20... - Page 6 SAFETY RULES SAFETY RULES LOAD Do not elevate the tower without using the stabilize legs. Do not move the tower after the load is elevated Place the tower over a flat and stable surface. Do not lean elements (like Do not install it in a place stairs, platforms, scaffoldings, where the use over the etc.) over the tower which can...
-
Page 7: Safety Rules
SAFETY RULES SAFETY RULES The load must be firmly placed Keep the hands and fingers over the support the nearest moved away to mobiles possible gravity center of the Do not lubricate the brake elements of the towers tower, in order to facilitate its system of the winch, the like profile unions. -
Page 8: Installing The Lifting Tower
INSTALLING THE LIFTING TOWER INSTALLING THE LIFTING TOWER Place the tower over a flat and stable surface to install the tower, discarding its use over rolling platforms or surfaces which would be able to bear as much its own weight as coupled For better security during the transport, these load. - Page 9 PLACING THE LOAD PLACING THE LOAD Before elevating the tower, you must unblock the security bolt located in the wheel transport system, so the wheel pass to stand position and the elevation process can start. Support in stand position for transport. (Only for LW 465R/LW 480R models) Extract the pin bolts and place it in horizontal position in order to locate...
-
Page 10: Winch Operation (Special Care)
LIFTING PROCESS PLACING THE LOAD HINT: IT IS POSSIBLE TO OBTAIN AN EXTRA HEIGHT, FLIPING THE SUPPORT. FOR THIS OPERATION, YOU MUST RETIRE THE CENTRAL SCREW AND TO CHANGE THE NOTE: BEFORE ELEVATING THE TOWER, CHECK THAT ALL BOLTS ARE POSITION ON THE SUPPORT PIECE. -
Page 11: Lifting Process
LIFTING PROCESS DESCENT/FOLDING PROCESS For the descent, we must to unblock the lower security bolt and turn the winch on inverse sense, the load bring down the profile up to the stand position. In that moment, we must to block the bolt for the transport use and we must unblock the new security bolt from the descended profile. - Page 12 LW 465R - LW480R - WT600 DESCENT/FOLDING PROCESS Unblocking process of a blocked section using one of these lifters Place them in the leg transport enclosure, taking into account that the two more longer leg In the case of the lifter would be loaded with a weight much more superior than the one recommended, it could happen than must be placed in the outside.
-
Page 13: Conformity Declaration
Lifts for Truss Systems This standard is orientated in two ways: By one side, the lifting towers adopt designs and materials in order to LW 465 R WORK® achieve a high security degree in magnitudes like load supported, LW 480 R WORK®... - Page 14 BGV C1, TESTS & CHECKS ANNUAL TEST ( passing the fourth year Checked by MODEL SERIAL NUMBER Date Signature Tested elements and conclusions INITIAL CHECK (First year) Checked by Signature Date Tested elements and conclusions ANNUAL TEST ( passing the fourth year Checked by Date Signature...
Need help?
Do you have a question about the LW 465 R and is the answer not in the manual?
Questions and answers