Page 2
EBA 721 LT Children must not operate the machine! Never leave the blade unattended. Do not extract or transport the blade without protection! Danger! Risk of injury! Do not reach beneath the blade! Paper clips or hard material will damage the cutting blade!
EBA 721 LT 1. General This instruction manual will help you to learn the safe and comfortable operation of this machine. Please read these operating instructions before putting the machine into operation and observe the safety regulations. 1.1 Safety Instructions...
2. Installation - Transport the machine on the pallet to its destination using a pallet-jack. - 6 strong people are required to lift the machine from the pallet. - The machine should be installed on a sturdy, dry and level floor. Danger! - The machine must not be located outside.
EBA 721 LT 2.2 Power supply The name plate (23) is located at the rear of the machine. - Data stated on the name plate - Voltage “ V “, - Frequency “Hz”, - Power consumption “A” must correspond to the values of the power supply unit.
3. Operation Danger! The machine may only be operated by trained persons who have also read and understood the operating and safety instructions. Danger! Check safety devices are complete and function prior to starting the machine and after replacing the blade. Checklist - Machine panels: All panels must be mounted...
EBA 721 LT 3.1 Operating elements (1) Safety two-handed control system (2) Backgauge control (3) Backgauge (4) Key switch (5) Main switch (6) Knocking-up block (7) Clamp pressure adjustment (8) Foot pedal (9) Airtable switch (10) Program number (11) Program step (12) LED „M“...
EBA 721 LT 3.5 Programming The control system enables 20 programs with up to 16 steps to be programmed. One step represents one measurement or max. 9 chain measurements. Program Step Memory £ Program up ¢ Program down Clear Delete...
4. Maintenance Danger! - Maintenance work may only be performed by trained staff. - Before replacing the blade or cutting stick switch off the main switch. - Disconnect from the mains before starting any service work or before removing the cover. Safety check According to §...
EBA 721 LT Turning or replacing the cutting stick - Turn the blade depth adjustment (27) to the top until it stops (spanner in tool set). - Remove spanner. Danger! Risk of injury! - Remove the cutting stick (26) with a small screwdriver.
4.2 Blade replacement A reduction in the cutting quality indicates that the blade must be sharpened or a blade change is necessary. Danger! Risk of injury! - The blade is extremely sharp. Do not remove or transport the blade without protection.
EBA 721 LT 5. Malfunctions Danger! Disconnect from the mains before starting any service work or before removing the cover. Malfunction: No display. Cause: Power supply. Remedy: - Plug in to the mains. - Mains switch on. - Check on-site fuse.
Page 21
Malfunction: Machine is switched on but cut cannot be performed. Cause: Safety clutch is activated. Remedy: Contact your dealer. Malfunction: The last sheet of paper is not completely cut. Remedy: Adjust the cutting depth (see Cutting stick) or replace or turn the cutting stick. Malfunction: Poor cutting quality or blade jams.
EBA 721 LT 6. Technical data Sound level DIN 45635-27: max. 73 dB(A) Minimum space requirement B x T: without side tables 130 cm x 151 cm with side tables 210 cm x 160 cm Clamping pressure 250 dN bis 2000 dN...
- Hiermede verklaren wij, dat de in de handel gebrachte machine - Com a presente, declaramos que o modelo da - Hermed erklæres, at produkttypen 721; 721 LT - folgenden einschlägigen Bestimmungen entspricht: - complies with the following provisons applying to it: - sont conformes aux dispositions pertinentes suivantes: - satisface las disposiciones pertinentes siguientes: - è...