Related Manuals for SMC Networks KQB2-F Series
Summary of Contents for SMC Networks KQB2-F Series
- Page 1 Doc. no. KQ*-OMY0033-A PRODUCT NAME FDA compliant Metal One-touch Fittings MODEL / Series / Product Number KQB2-F Series...
- Page 2 Contents 1. Safety instructions 2 to 3 2. Specific product precautions 4 to 9 3. Specifications 10 to 11 4. Troubleshooting 5. Construction...
- Page 3 FDA compliant Metal One-touch Fittings Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) , and other safety regulations.
- Page 4 FDA compliant Metal One-touch Fittings Safety Instructions Caution 1.The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary.
- Page 5 The components of the KQB2-F series may (2)The tubing bending radius in the vicinity of the slide due to changes in the internal pressure, fitting should be at least the minimum bending which may generate particles.
- Page 6 2. Specific Product Precautions（2） (8)When performing the piping work, turn the tightening tool in the horizontal direction to Mounting/Piping the hex. across flats of the stud so that any moment is not applied to the body. If the tool is in contact with the body, this may Caution cause the stud to come off.
- Page 7 and antistatic tubing (Series TA) are recommended. 2．Specific Product Precautions（3） (6)Do not use the ordinary fittings and tubing in (3)Drain flushing locations where spatter is generated. If condensation in the drain bowl is not emptied Spattering may result in a fire hazard. In such a on a regular basis, the bowl will overflow and place, use of flame resistant fittings (Series allow the condensation to enter the compressed...
- Page 8 4. Pull the tubing back gently to make sure it has a positive seal. Insufficient installation may 2．Specific Product Precautions（4） cause air to leak or the tubing to release. (3)Drain flushing As a guide for checking the tubing is not pulled Remove drainage from air filters regularly.
- Page 9 Chamfer Dimension for Female Thread 2．Specific Product Precautions（5） Caution Connection Thread Tightening Method (1) Chamfer dimension for female thread of the connection thread Caution Confirming to ISO 16030 (air pressure fluid (1) Connection thread: M5 and 10-32UNF dynamics – connection – ports and stud ends), Screw tightening torque is 1 to 1.5Nm the chamfer dimensions shown below are (2) Connection thread: R, NPT...
- Page 10 2．Specific Product Precautions（6） Precautions for use with non-SMC tubing Recommended Piping Conditions Caution (1) When connecting piping to the One-touch (1)When used with tubing other than those from fitting, use pipe length with sufficient margin, SMC, due to their properties, series KQB2-F in accordance with the piping conditions are not subject to warranty.
- Page 11 3. Specifications Applicable Tubing Note) Tubing material FEP, PFA, Nylon, Soft nylon, Polyurethane, Polyolefin ø 3.2, ø 4, ø 6, ø 8, ø 10, ø 12, ø 16 Tubing O.D. ø 1/8", ø 5/32", ø 1/4", ø 5/16", ø 3/8", ø 1/2" Note: Considering the product application, FDA compliant products are recommended.
- Page 12 Cross Reference Table of the Inner Sleeve (Inch size) Tubing material Applicable inner sleeve Tubing O.D. TH/TIH TL/TIL Part no. Length (FEP) (Super PFA) TH0402 TJG-0402 ø 5/32" TH0425 TJG-0425 TL0403 TJG-0403 TIHB07 TIL07 TJG-0604 ø 1/4" TIHA07 TJG-0746 ø 5/16" TH0806 TL0806 TJG-0806...
- Page 13 5. Construction Connection thread: R,NPT Male elbow Male connector Connection thread: G Male elbow Male connector Description Material Release button Stainless steel 304 Guide 1 Stainless steel 304 Guide 2 Stainless steel 304 Chuck Stainless steel 304 FDA Compliant FKM (NSF H1 grease) Seal Male connector body C3604 (Electroless nickel plating)
- Page 14 Revision history A: Cleaning added 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. ©...
Need help?
Do you have a question about the KQB2-F Series and is the answer not in the manual?
Questions and answers