1. Manuals
  2. Brands
  3. Fema Manuals
  4. Farm Equipment
  5. Unverferth 2070
  6. Assembly manual

Fema Unverferth 2070 Assembly Manual

Dual-auger
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Grain Carts
Dual-Auger Model 2070
ASSEMBLY MANUAL
Beginning With Serial Number B37100100
Part No. 2007938

Advertisement

Table of Contents
loading

Related Manuals for Fema Unverferth 2070

Summary of Contents for Fema Unverferth 2070

  • Page 1 Grain Carts Dual-Auger Model 2070 ASSEMBLY MANUAL Beginning With Serial Number B37100100 Part No. 2007938...
  • Page 2 — Set Up Unverferth 2070 Notes...

  • Page 3: Table Of Contents

    — Set Up Unverferth 2070 Section I Set Up General Safety Information ......................1-4 Unpacking Grain Carts ....................... 1-6 Track Axle Assembly ........................ 1-10 Steerable Tandem Assembly ....................1-12 Tank Assembly ......................... 1-28 Auger Assembly ........................1-56 Sideboard Assembly ......................... 1-67 Electrical Diagram ........................

  • Page 4: General Safety Information

    — Set Up Unverferth 2070 General Safety Information • ELECTROCUTION WILL CAUSE SERIOUS INJURY OR DEATH. THE GRAIN CART IS NOT INSULATED. KEEP AWAY FROM ALL ELECTRICAL LINES AND DEVICES. ELECTROCU- TION CAN OCCUR WITHOUT DIRECT CONTACT. • ENTANGLEMENT WITH THE DRIVELINE WILL CAUSE SERIOUS INJURY OR DEATH.
  • Page 5 — Set Up Unverferth 2070 General Safety Information (continued) • HYDRAULIC SYSTEM MUST BE PURGED OF AIR BEFORE OPERATING TO PREVENT SERIOUS INJURY OR DEATH. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED. BE SURE ALL LIFTING DEVICES AND SUPPORTS ARE RATED FOR THE LOADS BEING HOISTED.

  • Page 6: Unpacking Grain Carts

    — Set Up Unverferth 2070 Unpacking Grain Cart • Use care not to damage scale spindle and wiring harness. Damage to scale spindle or wiring harness will give incorrect scale information. Once the cart has been removed from the container, position cart on a level surface area, block the wheel and disconnect the towing vehicle.
  • Page 7 — Set Up Unverferth 2070 Unpacking Grain Cart (continued) Using the panel lifting device and a safe lifting device rated at a minimum of 300 lbs. (136 kg.), remove the tank panels and sideboards from the top of the hopper shipping bundle.
  • Page 8 — Set Up Unverferth 2070 Unpacking Grain Cart (continued) Using safe lifting device rated at a minimum of 2,000 lbs. (909 kg.), remove the tongue assembly (FIG. 1-6). Place the tongue assembly away from the grain cart. FIG. 1-6 Using a safe lifting device rated at a minimum of 1,000 lbs. (455 kg.), support the front grain cart shipping bundle.
  • Page 9 — Set Up Unverferth 2070 Unpacking Grain Cart (continued) Using a safe lifting device rated at a minimum of 250 lbs. (114 kg.) and attached to the lifting lugs on the front hopper yellow shipping bracket, to support the bundle (FIG. 1-8).

  • Page 10: Track Axle Assembly

    — Set Up Unverferth 2070 Track Axle Assembly • Damage to scale spindle wiring harness will cause scale to work improperly. Locate the axle on the bottom-rear shipping bundle. Sixteen 1”-8UNC x 3” Capscrews (9390-187), 1” Flat Washer (9405-118), 1” Lock Washer Using a safe lifting device rated at (9404-041), and 1”-8UNC Hex Nuts (9394-020)
  • Page 11 — Set Up Unverferth 2070 Track Axle Assembly (continued) Insert the pivot shafts (282102) into the axle (282069G or 282069R) and secure with 1”-8UNC x 10” capscrews (9390-464) and 1”-8UNC lock nuts (92199) (FIG. 1-13). Torque hardware according to “Torque Chart” located in this manual.

  • Page 12: Steerable Tandem Assembly

    — Set Up Unverferth 2070 Steerable Tandem Assembly • Damage to scale spindle wiring harness will cause scale to work improperly. Using a safe lifting device rated at a minimum of 2,000 lbs. (909 kg.), support left-hand front and rear steering linkage assembly. Loosely attach the steering linkage assembly to the bottom and sides using twelve 1”-8UNC x 3”...
  • Page 13 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Using a safe lifting device rated at a minimum of 250 lbs. (114 kg.), support the axle truss weldment (273415B). Position axle truss weldments (273415B) over the front and rear steering linkage assembly area of the grain cart. Loosely attach the axle truss weldments to the steering linkage assemblies with sixteen 1”-8UNC x 3”...
  • Page 14 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) 9004613 - Remove and save the front, left-hand pivot bushing weldment (286174B) 286182 - Wash with self-lubricating bushing (9004613), washer (286182), 1”-8UNC x 3” cap- 9390-187 1"-8UN screws (9390-187), 1” lock washers (9404-042), and 1”-8UNC hex nuts...
  • Page 15 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) 9004613 - Self Lubricating Bushing Remove and save the front, right-hand 286182 - Washer 2 1/2" OD x 1,531" ID pivot bushing weldment (286175B) with self-lubricating bushing (9004613), 9390-187 1"-8UNC x 3" HCS washer (286182), 1”-8UNC x 3”...
  • Page 16 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Remove and save the rock shaft plate (286228B), 1/2”-13UNC x 2 1/2” capscrews (9390-105), 1/2” lock washers (9404-025), self lubricating bushing (9006055), and 1/2” SAE flat washers (9405-086). (FIG. 1-20) 1/2" SAE Flat Washers (9405-086)
  • Page 17 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Using a safe lifting device rated at a minimum of 150 lbs. (68 kg.), support the left- hand rocker link weldment (286181B). (FIG. 1-21) Remove and save the 1 1/4” Dia. x 3 3/16” pin weldment (283725), 1 1/4” Dia. x 4”...
  • Page 18 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Secure the front of the left-hand rocker link weldment (286181B) with left-hand pivot bushing weldment (286174B) to the front, left-hand steering linkage assembly with previously removed 1”-8UNC x 3” capscrews (9390-187), 1” lock washers (9404-042), and 1”-8UNC hex nuts (9394-020).
  • Page 19 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Secure the rear of the left-hand rocker link weldment (286181B) with left-hand pivot bushing weldment (286174B) to the rear, left-hand steering linkage assembly with previously removed 1”-8UNC x 3 1/2” capscrews (9390-189), 1” lock washers (9404-042), and 1”-8UNC hex nuts (9394-020).
  • Page 20 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Secure the front of the right-hand rocker link weldment (286131B) with right-hand pivot bushing weldment (286175B) to the front, right-hand steering linkage assembly with previously removed 1”-8UNC x 3” capscrews (9390-187), 1” lock washers (9404-042), and 1”-8UNC hex nuts (9394-020).
  • Page 21 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Secure the rear of the right-hand rocker link weldment (286131B) with right-hand pivot bushing weldment (286175B) to the rear, right-hand steering linkage assembly with previously removed 1”-8UNC x 3 1/2” capscrews (9390-189), 1” lock washers (9404-042), and 1”-8UNC hex nuts (9394-020).
  • Page 22 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Secure the middle of the left-hand rocker link weldment (286181B) by placing the two halves of the self lubricating bushing (9006055) around the link and secure with the previ- ously removed rock shaft plate (286228B), 1/2”-13UNC x 2 1/2” capscrews (9390-105), 1/2”...
  • Page 23 — Set Up Unverferth 2070 SSEMBLE LARGE TO FITTING. Steerable Tandem Assembly (continued) ACES Torque hardware according to “Torque Chart” located in this manual. Remove the caps from the cylinder base end fittings and assemble the REMOVE CAP. ASSEMBLE LARGE large hose end to the fittings.
  • Page 24 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Set each cylinder clevis ends equal distance from the cylinder body (FIG. 1-31). Attach the rocker link weldments to the turnbuckles with the pin and snap ring provided. (FIG. 1-31) FIG. 1-31 SET EACH CYLINDER CLEVIS REMOVE PIN &...
  • Page 25 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Check the hub faces. Place a long straight board or tube along the face of the hubs. Adjust the tie rods by hub pivot until the hub faces are in-line. NOTE: Alignment will be checked again after the wheel and tire assembles are attached.
  • Page 26 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Route the 1/4” x 430” hose (9004637) along the bottom of the cart with the 9/16-18 JIC female end towards the rear of the cart. Attach the 1/4” x 430” hose (9004637) to the bottom of the cart with five double hose clamps (9003816), top clamp plate (9003814) and 5/16”-18UNC x 1 1/2”...
  • Page 27 — Set Up Unverferth 2070 Steerable Tandem Assembly (continued) Using a safe lifting device rated at a minimum of 1,500 lbs. (682 kg.), attach the wheel and tire assemblies. (FIG. 1-34) Secure the wheel and tire assemblies with the M22 x 1.5 flanged cap nuts (97319).

  • Page 28: Tank Assembly

    — Set Up Unverferth 2070 Tank Assembly • Loosely install hardware. Do not tighten until instructed to do so. This will allow optimum fitment of the panels and braces. • Make sure the grain cart is level. Use the panel lifting device provided and a safe lifting device rated at a minimum of...
  • Page 29 — Set Up Unverferth 2070 Tank Assembly (Continued) Locate six splice trim hopper brace weldments (273085G or 273085R). Splice Trim Hopper Brace Weldment Use a safe lifting device rated at a (273085G or 273085R) minimum of 100 lbs. (45 kg.) to install...
  • Page 30 — Set Up Unverferth 2070 Tank Assembly (Continued) TRACK MODELS Tracks ONLY 2nd & 3rd Panels FIG. 1-38 Outside View of Cart Locate eight outside trim plates (273490G or 273490R) and inside panel brace weldments (273367B). Also lo- cate eight side hopper panels. (FIG.
  • Page 31 — Set Up Unverferth 2070 Tank Assembly (Continued) Using the panel lifting device provided and a safe lifting device rated at a minimum of 300 lbs. (136 kg.), lift the hopper panels into position. Loosely secure panels to the panel braces and along the bottom of the hopper panel with 3/8”-16UNC x 1 1/4”...
  • Page 32 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the left-hand front/1st hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-41 & FIG. 1-42) FIG. 1-41 Track Cart Left-Hand 1st Hopper Panel...
  • Page 33 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the left-hand 2nd hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-43 & FIG. 1-44) STEERABLE TANDEM CART ONLY Secure the bottom of the 2nd hopper panel with wheel well brace (273417B), 3/8”-16UNC x 1 1/4”...
  • Page 34 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the left-hand 3rd hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-45 & FIG. 1-46) STEERABLE TANDEM CART ONLY Secure the bottom of the 3rd hopper panel with wheel well brace (273417B), 3/8”-16UNC x 1 1/4”...
  • Page 35 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the left-hand rear/4th hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-47 & FIG. 1-48) Track Cart FIG. 1-47 Left-Hand 4th Hopper Panel...
  • Page 36 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the right-hand front/1st hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-49 & FIG. 1-50) Track Cart FIG. 1-49 Right-Hand 1st Hopper Panel...
  • Page 37 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the right-hand 2nd hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-51 & FIG. 1-52) STEERABLE TANDEM CART ONLY Secure the bottom of the 2nd hopper panel with wheel well brace (273417B), 3/8”-16UNC x 1 1/4”...
  • Page 38 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the right-hand 3rd hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-53 & FIG. 1-54) STEERABLE TANDEM CART ONLY Secure the bottom of the 3rd hopper panel with wheel well brace (273417B), 3/8”-16UNC x 1 1/4”...
  • Page 39 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the right-hand rear/4th hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). (FIG. 1-55 & FIG. 1-56) Track Cart FIG. 1-55 Right-Hand 4th Hopper Panel...
  • Page 40 — Set Up Unverferth 2070 Tank Assembly (Continued) Loosely attach the left-hand exterior support brace to the hopper panel FIG. 1-57 with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). Use clamps to help make sure the exterior support braces are properly positioned on the cart.
  • Page 41 — Set Up Unverferth 2070 Tank Assembly (Continued) Loosely attach the right-hand exterior support brace to the hopper panel FIG. 1-59 with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). Use clamps to help make sure the exterior support braces are properly positioned on the cart.
  • Page 42 — Set Up Unverferth 2070 Tank Assembly (Continued) Loosely attach the right-front exterior FIG. 1-61 support brace to the hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). Secure the right-front exterior support brace to the grain cart with 5/8”-11UNC x 2”...
  • Page 43 — Set Up Unverferth 2070 Tank Assembly (Continued) Loosely attach the front and side hopper panels with front hopper brace weldments (273334B), using 3/8”-16UNC x 1 1/4” carriage bolts, 3/8”-16UNC x 1” flange screws (91262), and 3/8”-16UNC large flange nuts (91263).
  • Page 44 — Set Up Unverferth 2070 Tank Assembly (Continued) level - Bing Page 1 of 1 Use the panel lifting device provided and a safe lifting device rated at a minimum of 1,000 lbs. (454 kg.), loosely attach the rear hopper panels with 3/8”-16UNC x 1 1/4”...
  • Page 45 — Set Up Unverferth 2070 Tank Assembly (Continued) Use safe lifting device rated at a minimum of 300 lbs. (136 kg.), loosely attach the left-rear brace (273379G or 273379R) to the left-rear hopper panel with 3/8”-16UNC x 1 1/4” carriage bolts (9388-052) and 3/8”-16UNC large flange nuts (91263). Attach the bottom of the left-rear brace (273379G or 273379R) to the left-rear panel with 3/8”-...
  • Page 46 — Set Up Unverferth 2070 Tank Assembly (Continued) Using a safe lifting device rated at a minimum of 100 lbs. (45 kg.), loosely attach the cross tube weldments (273149B) with 1/2”-13UNC x 1 1/2” flange screws (9005705) and 1/2”-13UNC lock nuts (9003397).
  • Page 47 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the rear trim plate (273179G or 273179R) to the right-rear hopper FIG. 1-72 panel with 3/8”-16UNC x 1 1/4” car- riage bolts (9388-052) and 3/8”-16UNC 3/8”-16UNC x 1 1/4” large flange nuts (91263).
  • Page 48 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the red light (9006345) to the left-rear of the cart with #10-32UNF x 1 1/4” phillips pan head machine screws (903172-350), #10 lock washers (9404-013), and #10-32UNF hex nuts (9830-016). FIG. 1-75...
  • Page 49 — Set Up Unverferth 2070 Tank Assembly (Continued) Attach the red light (9006345) to the right-rear of the cart with #10-32UNF x 1 1/4” phillips pan head machine screws (903172-350), #10 lock washers (9404-013), and #10- 32UNF hex nuts (9830-016).
  • Page 50 — Set Up Unverferth 2070 Tank Assembly (Continued) Route the running light/clearance wir- FIG. 1-80 ing harness (9005890) along the up- per left-hand side of the hopper and attach the four amber clearance light Clearance harnesses (9005542). Reference “Elec- Light Harness trical Diagram”.
  • Page 51 — Set Up Unverferth 2070 Tank Assembly (Continued) Route the running light/clearance wiring harness (9009368) along the upper right-hand side of the hopper and attach the four amber running light pig tails. (Reference Electrical Diagram) Right-Hand Running Light/ Cable Tie Clearance Harness (9009368) FIG.
  • Page 52 — Set Up Unverferth 2070 Tank Assembly (Continued) TRACK CART ONLY Use safe lifting device rated at a minimum of 100 lbs. (45 kg.), loosely attach the cross tube weldments (273347B) with 1/2”-13UNC x 1 1/2” flange screws (9005705) and 1/2”- 13UNC lock nuts (9003397).
  • Page 53 — Set Up Unverferth 2070 Tank Assembly (Continued) (continued) STEERABLE TANDEM CART ONLY Use safe lifting device rated at a minimum of 100 lbs. (45 kg.), loosely attach the cross tube weldments (273347B) with 1/2”-13UNC x 1 1/2” flange screws (9005705) and 1/2”- 13UNC lock nuts (9003397).
  • Page 54 — Set Up Unverferth 2070 Tank Assembly (Continued) TRACK CART ONLY Use safe lifting device rated at a minimum of 100 lbs. (45 kg.), loosely attach the cross tube weldments (273149B) with 1/2”-13UNC x 1 1/2” flange screws (9005705) and 1/2”- 13UNC lock nuts (9003397).
  • Page 55 — Set Up Unverferth 2070 Tank Assembly (Continued) (continued) STEERABLE TANDEM CART ONLY Use safe lifting device rated at a minimum of 100 lbs. (45 kg.), loosely attach the cross tube weldments (273347B) with 1/2”-13UNC x 1 1/2” flange screws (9005705) and 1/2”- 13UNC lock nuts (9003397).

  • Page 56: Auger Assembly

    — Set Up Unverferth 2070 Auger Assembly Lubricate the face of the cart where the lower auger will attach. FIG. 1-88 Grease Face Install the 2 3/4” Dia. x 17 5/8” shaft (273779) into the front of the cart FIG. 1-89 and secure using two 7/8”-9UNC x...
  • Page 57 — Set Up Unverferth 2070 Auger Assembly (Continued) Remove and save the cover (9004729) from the lower section of the vertical auger. 5/8”-11UNC x 1 3/4” Capscrews (9390-123) Cover & 5/8” Lock Washers (9004729) (9404-030) Upper Fold Plate (271119B) with Nylon Fold Slide (271124) 5/8”...
  • Page 58 — Set Up Unverferth 2070 Auger Assembly (Continued) Using a safe lifting device rated at a minimum of 1,500 lbs. (682 kg.), align the holes in the back side of the lower auger with the holes in the cart. NOTE: Horizontal auger shaft must go through the front of the lower auger as shown in FIG.
  • Page 59 — Set Up Unverferth 2070 Auger Assembly (Continued) Attach the upper portion of the lower auger to the cart with lower fold FIG. 1-93 plate (284518B) with nylon fold slide (271124), upper fold plate (271119B) with nylon fold slide (271124), 5/8”- 11UNC x 1 3/4”...
  • Page 60 — Set Up Unverferth 2070 Auger Assembly (Continued) Install the tilt cylinder to the cart. Attach the base end to the cart with 1” Dia. x 3 1/2” pin (804572) and 3/16” Dia. x 2” cotter pins (9391-046). The rod end attaches to the auger with 1”...
  • Page 61 — Set Up Unverferth 2070 Auger Assembly (Continued) Remove the auger hinge weldments and fold linkage weldment from the lower auger assembly. Reattach the auger hinge weldments and fold linkage weldment to the upper auger assembly with 13/16” flat washers (9234PL), 3/4” lock washers (9404-034), and grade 8 3/4”-10UNC x 2 1/4”...
  • Page 62 — Set Up Unverferth 2070 Auger Assembly (Continued) Use safe lifting device rated at a minimum of 1,500 lbs. (682 kg.), place upper auger into position. Align Auger Tubes FIG. 1-97 1-62...
  • Page 63 — Set Up Unverferth 2070 Auger Assembly (Continued) Insert the auger pivot pin (276561) through auger hinge and spacer bushing (273374G or 273374R). FIG. 1-98 5/8”-11UNC x 2” Capscrew (9390-124), 5/8” Flat Washer (9405-098) & 5/8”-11UNC Lock Nut (9003398) Spacer Bushing...
  • Page 64 — Set Up Unverferth 2070 Auger Assembly (Continued) Attach the upper pulley. Insert the taper lock bushing with keyway. Insert the keyway. Secure upper pulley with Using a straight edge, align the upper and lower pulleys. FIG. 1-100 Torque hardware.
  • Page 65 — Set Up Unverferth 2070 Auger Assembly (Continued) Belt tension is adjusted with hex nuts below the spring, FIG. 1-102. FIG. 1-102 Use hex nuts to All belt tension MUST be released adjust tension from linkage. Loosen outer hex nut and adjust inner nut to establish a 3 1/16"...
  • Page 66 — Set Up Unverferth 2070 Auger Assembly (Continued) Attach the belt cover (9004729). Attach Belt Engage the belt tensioner (FIG. 1-105). Cover Handle down is in engaged position FIG. 1-105 FIG. 1-106 Handle up is in disengaged position 1-66...

  • Page 67: Sideboard Assembly

    — Set Up Unverferth 2070 Sideboard Assembly Loosely install the hinges (9004626) on the left and right sideboards with 5/16”-18UNC x 3/4” large flange screws (91256) and 5/16”-18UNC large flange nuts (91257). FIG. 1-108 Attach the sideboard braces (273529B Front Sideboard and 273530B) to the front and rear FIG.
  • Page 68 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Using the panel lifting device provided Front Sideboard and a safe lifting device rated at a FIG. 1-111 Front Sideboard (273835B) (273835B) minimum of 200 lbs. (91 kg.), attach front sideboard (273835B) with braces (273529B and 273530B) to the front hopper panels with 3/8”-16UNC x 3/4”...
  • Page 69 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Using the panel lifting device provided and a safe lifting device rated at a Left-Front Sideboard Left-Front Sideboard (273713B) (273713B) minimum of 200 lbs. (91 kg.), attach left-front sideboard (273713B) with hinge (9004626) to the left-front/1st hopper panel with 5/16”-18UNC x 3/4”...
  • Page 70 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a minimum of 200 lbs. (91 kg.), attach Right-Front Sideboard Right-Front Sideboard (273714B) (273714B) right-front sideboard (273714B) with hinge (9004626) to the right-front/1st hopper panel with 5/16”-18UNC x 3/4”...
  • Page 71 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Attach the brackets (300977B) to the right-hand side of the tarp bow weld- Tarp Bow ments (273359B) with 3/8”-16UNC x (273359B) 1” carriage bolts (9388-051) and 3/8”- Right-Hand 16UNC large flange nuts (91263).
  • Page 72 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- Left-2nd Sideboard Left-2nd Sideboard (273299B) mum of 200 lbs. (91 kg.), attach left- (273299B) 2nd sideboard (273299B) with hinges (9004626) to the left/2nd hopper panel with 5/16”-18UNC x 3/4”...
  • Page 73 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- Right-2nd Sideboard (273303B) Right-2nd Sideboard mum of 200 lbs. (91 kg.), attach right- (273303B) 2nd sideboard (273303B) with hinges (9004626) to the right/2nd hopper panel with 5/16”-18UNC x 3/4”...
  • Page 74 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use a safe lifting device rated at a minimum of 50 lbs. (23 kg.), loosely assemble the sideboard brace weldment (273325B) to the sideboards and the hopper cross brace with 3/8”-16UNC x 3/4” flange screws (91262) and 3/8”-16UNC large flange nuts (91263).
  • Page 75 — Set Up Unverferth 2070 Sideboard Assembly (Continued) NOTE: The right-hand side of the tarp bow weldments (273359B) with bracket (300977B) will be secured to the sideboards later on with the tarp latch plates. Insert two tarp bow weldment (273359B) tabs into the left-hand sideboard.
  • Page 76 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- Left-3rd Sideboard Left-3rd Sideboard (273300B) mum of 200 lbs. (91 kg.), attach left- (273300B) 3rd sideboard (273300B) with hinges (9004626) to the left/3rd hopper panel with 5/16”-18UNC x 3/4”...
  • Page 77 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- Right-3rd Sideboard (273304B) mum of 200 lbs. (91 kg.), attach right- Right-3rd Sideboard (273304B) 3rd sideboard (273304B) with hinges (9004626) to the right/3rd hopper panel with 5/16”-18UNC x 3/4”...
  • Page 78 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use a safe lifting device rated at a minimum of 50 lbs. (23 kg.), loosely assemble the sideboard brace weldment (273325B) to the sideboards and the hopper cross brace with 3/8”-16UNC x 3/4” flange screws (91262) and 3/8”-16UNC large flange nuts (91263).
  • Page 79 — Set Up Unverferth 2070 Sideboard Assembly (Continued) NOTE: The right-hand side of the tarp bow weldments (273359B) with bracket (300977B) will be secured to the sideboards later on with the tarp latch plates. Insert two tarp bow weldment (273359B) tabs into the left-hand sideboard.
  • Page 80 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- mum of 200 lbs. (91 kg.), attach left- Left-Rear Sideboard Left-Rear Sideboard (273715B) (273715B) 4th sideboard (273300B) with hinges (9004626) to the left/4th hopper panel with 5/16”-18UNC x 3/4”...
  • Page 81 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a mini- Right-Rear Sideboard (273716B) Right-Rear Sideboard mum of 200 lbs. (91 kg.), attach right- (273716B) 4th sideboard (273304B) with hinges (9004626) to the right/4th hopper panel with 5/16”-18UNC x 3/4”...
  • Page 82 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use a safe lifting device rated at a minimum of 50 lbs. (23 kg.), loosely assemble the sideboard brace weldment (273325B) to the sideboards and the hopper cross brace with 3/8”-16UNC x 3/4” flange screws (91262) and 3/8”-16UNC large flange nuts (91263).
  • Page 83 — Set Up Unverferth 2070 Sideboard Assembly (Continued) NOTE: The right-hand side of the tarp bow weldments (273359B) with bracket (300977B) will be secured to the sideboards later on with the tarp latch plates. Insert two tarp bow weldment (273359B) tabs into the left-hand sideboard.
  • Page 84 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Use safe lifting device rated at a minimum of 200 lbs. (91 kg.), attach Rear Sideboard (273286B) Rear Sideboard (273286B) rear sideboard (273286B) with braces (273529B and 273530B) to the rear hopper panels with 3/8”-16UNC x 3/4”...
  • Page 85 — Set Up Unverferth 2070 Sideboard Assembly (Continued) Attach the rear sideboard (273286B) to the left-rear sideboard (273715B) with FIG. 1-157 corner plate (273708B), 3/8”-16UNC x 1” large flange screw (91262), and 3/8”-16UNC large flange nuts (91263). Corner (273708B), 3/8”-16UNC x 1” Large Flange Screws (91262) and 3/8”-16UNC...

  • Page 86: Electrical Diagram

    — Set Up Unverferth 2070 Electrical Diagram To Tractor 7-Way Plug (92450) Proximity Switch (9007223) Clearance Light Harness (9005542) Auger Light Switch Harness Front Wiring Harness (9008107) (9008106) Work Light (9008957) Amber Clearance Light (9005529) Left-Hand Running Light/ Right-Hand Running Light/...

  • Page 87: Tongue Assembly

    — Set Up Unverferth 2070 Tongue Assembly Remove the 2” Dia. x 7 13/16” pins (273368), 5/8”-11UNC x 3 1/2” capscrews (9390-130), 5/8”- 11UNC lock nuts (95905) from the tongue assembly (FIG. 1-159) Use safe lifting device rated at a minimum of 2,000 lbs. (909 kg.), lift the tongue assembly into position.

  • Page 88: Ladder Assembly

    — Set Up Unverferth 2070 Ladder Assembly Using a safe lifting device rated at a minimum of 100 lbs. (46 kg.) attach the ladder assembly to the right-hand side panel with 1/2”-13UNC x 1” car- riage bolts (9388-102), 1/2” USS flat washers (9405-088), and 1/2”-13UNC...

  • Page 89: Jack Installation

    — Set Up Unverferth 2070 Jack Installation • UNHITCHING A LOADED CART CAN CAUSE SERIOUS INJURY OR DEATH DUE TO TONGUE RISING OR FALLING. ALWAYS HAVE A LOADED CART ATTACHED TO A TRACTOR. THE JACK IS INTENDED TO SUPPORT AN EMPTY CART ONLY.

  • Page 90: Transport Chain

    — Set Up Unverferth 2070 Transport Chain Attach with transport chain (9004898) to the front of the tongue assem- FIG. 1-163 bly with 1”-8UNC x 4” capscrew (91299-191) and 1”-8UNC lock nut (92199) (FIG. 1-163). SMV Emblem Before the cart is used the reflective sur- face of the SMV must face rearward.

  • Page 91: Toolbox Installation

    — Set Up Unverferth 2070 Toolbox Installation Attach toolbox (9008634) to the toolbox mounting bracket with two 1/4”-20UNC x 1 1/4” capscrews (9390-006), fender washers (94763), 1/4” USS flat washers (9405-064), and 1/4”-20UNC lock nuts (9936). FIG. 1-165 FIG. 1-165...

  • Page 92: Weather Guard Tarp Installation

    — Set Up Unverferth 2070 Weather Guard Tarp Installation • NEVER ENTER CART WITH AUGER OR TRACTOR RUNNING. SERIOUS INJURY OR DEATH CAN OCCUR DUE TO ENTANGLEMENT WITH ROTATING COMPONENTS. ALWAYS STOP ENGINE AND REMOVE KEY BEFORE ENTERING CART. •...
  • Page 93 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) Position the end caps (276756B and 296115B) on the cart aligning with the correspond- ing bolt holes. Secure the end caps (276756B and 296115B) using 3/8”-16UNC x 3/4” large flange capscrews (95585), 3/8”-16UNC large flange nuts (91263), and 1/4”-14 x 1”...
  • Page 94 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) Tarp Installation NOTE: Ensure doublers are inside the sideboard lip. See Figure 2-14. Install eight long tarp bows (291289B) across top of the cart, using RH tarp bow mount- ing brackets (283425B), LH tarp bow mounting brackets (283427B), doubler brackets (294678B), 3/8”-16UNC x 3”...
  • Page 95 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) NOTE: Ensure capscrew head (902703- 046) is flush with the top of bow weldment Capscrew (296115B). FIG. 1-171 (902703-046) Tighten all hardware. Tarp Bow (296115B) FIG. 1-171 1-95...
  • Page 96 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) Attach Cable Assemblies Install four tarp cables across the top Attach Tarp Cables using 3/8”-16UNC x 6” capscrew Capscrew (9008315), 3/8” star/lock wash- (9008315) er (9005688), 3/8” fender washer (9005696) and bracket & U-nut as- Lock sembly (281712B).
  • Page 97 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Optional) (Continued) Attaching Tarp On a clean floor, lay the tarp out flat with the raw edge of the hems and pockets down and the exterior side facing up. (FIG. 1-176) U-Clamp #10-16 x 3/4”...
  • Page 98 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Optional) (Continued) Insert knotted stretch rope/bungee (221722) through 3/8” flat washer (9405-074), plastic tube (221668), end plug (9004947) and hose (TA806225). Place these items as an assembly into front end of 2” tube (273381) and press the end plug (9004947) into the end of the tube.
  • Page 99 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) Using appropriate lifting device rated at a minimum of 250 lbs. (114 kg.) position tarp on top of left hand side of cart. Place the stationary tube of the assembled tarp into the hold down brackets (266689B) located on the left- hand side of the cart.
  • Page 100 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Continued) Unroll the tarp and insert stretch FIG. 1-181 cord through the top of the eye bolt (9004548) and knot off. See Fig. 1-181. 9004548 & 91263 1-100...
  • Page 101 — Set Up Unverferth 2070 Weather Guard Tarp Installation (Optional) (Continued) Hand Crank Handle Insert U-joint (9004977) over splined FIG. 1-182 9005089 coupling (273381) and secure with wire lynch pin (9005305). Insert crank 903172-450 handle (221749) into U-joint and secure 9398-012 with roll pin (9391-180).

  • Page 102: Complete Torque Chart

    — Set Up Unverferth 2070 Complete Torque Chart Capscrews - Grade 5 NOTE: • Grade 5 capscrews can be identified by three radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.
  • Page 103 — Set Up Unverferth 2070 Complete Torque Chart (continued) Capscrews - Grade 8 NOTE: • Grade 8 capscrews can be identified by six radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.
  • Page 104 www.unverferth.com L:\OMUNVERFERTH\1128GRAINCART\2005520.indd///April 2018-0//February 2023-1...

Table of Contents