Advertisement
2. INTRODUCTION
Features tilt and swivel head for optimum air circulation. Remote control operation and fully guarded fan blades for ease of use and extra safety.
Smooth running motor powers both fan blades and head oscillation. Timer function allows user to preset running time between 30 minutes - 4
hours. Sleep mode for gradual reduction of fan speed. Supplied with wall bracket for quick and easy installation.
3. SPECIFICATION
Model No: ........................................................ SWF18WR.V2
Fan Diameter: ....................................................450mm (18")
Height: ....................................................................... 550mm
Speeds: ................................................................................ 3
Oscillation: ....................................................................... Yes
Maximum fan flow rate: ........................................ 97.2m
Maximum air velocity: .................................................. 2.8m/s
Fan power input (P): ........................................................65W
Service value (SV): ......................................... 1.7(m³/min)/W
Standby power consumption (Psb):................................0.2W
Fan sound power level (Lwa): ................................... 57dB(A)
Supply: ...........................................................................230V
Height: ....................................................................... 550mm
Measurement standard for service value: .... IEC 60879:1986
4. ASSEMBLY
4.1.
Remove the rear grill mounting nut by turning it counter-clockwise.
4.1.1.
Place the rear grill onto the motor housing aligning the 3 raised knobs on the top of
the motor housing with the three holes on the grill. fig.1.
4.1.2.
Place the rear grill mounting nut over spindle and and tighten clockwise. fig.2.
4.1.3.
Align the blade with the shaft and slide into position. Secure in position by tightening
the blade knob counter-clockwise. fig.3.
4.1.4.
Align the front grill with the rear grill and push the clips together to secure .
4.2.
WALL MOUNTING
4.2.1.
Position the wall mounting bracket on the wall where the fan will be mounted.
ensure the blades are more than 2.3 m above floor.
4.2.2.
Use the bracket as a template and mark the two holes ready for drilling. fig.4.
4.2.3.
Use either fixings supplied or proprietory wall fixings, ensure fixings chosen are
suitable for the type of wall and the weight of the fan.
4.2.4.
Drill two holes suitable for the wall fixings.
4.2.5.
Attach bracket to wall.
4.2.6.
Slide fan back plate over bracket to hang fan from wall.
4.3.
BATTERY INSTALLATION
4.3.1.
To use remote control, open the cover on the back of the remote control unit fig.5, and
insert 2 x AAA batteries ensure they are correctly position according to polarity see diagram in battery compartment.
fig.4
5. OPERATION
5.1.
Position the fan on a level and dry wall surface.
5.2.
Plug the power cable into the socket and switch on the power supply.
5.3.
FAN CONTROL PANEL
5.3.1.
LED TIMER :- Visual display of time setting can only be set from remote
control.
LED FAN SPEED :- Visual display of speed.
5.3.2.
5.3.3.
FAN ON/SPEED CONTROL BUTTON :- Press to switch on, press again
to scroll trough speed settings.
5.3.4.
OSCILLATING BUTTON :- Press to switch on oscillation, press again to
switch off oscillation.
5.3.5.
STOP BUTTON :- Switches fan off
5.4.
REMOTE CONTROL
5.4.1.
FAN ON/SPEED CONTROL BUTTON :- Press to switch on, press again
to scroll trough speed settings.
5.4.2.
OSCILLATING BUTTON :- Press to switch on oscillation, press again to
switch off oscillation.
5.4.3.
STOP BUTTON :- Switches fan off.
© Jack Sealey Limited
/min
3
fig.5
Original Language Version
fig.1
fig.2
fig.3
fig.6
fig.7
SWF18WR.V2 Issue 1 18/02/21
Advertisement
