Lights - Whirlpool WRS555SIHZ Owner's Manual

4. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to 3
months to ensure maximum efficiency.
If you need to clean the condenser:
� Remove the base grille. See the "Door Removal"
instructions, either in the Owner's Manual or in the
separate instruction sheet provided with your refrigerator.
� Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille, and the front surface area
of the condenser.
� Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.

Lights

Not all bulbs will fit your refrigerator. Be sure to replace the bulb
with one of the same size, shape, and wattage.
IMPORTANT: The light bulbs in both the refrigerator and freezer
compartments of your new refrigerator may use LED technology.
On some models, the LED light bulbs in the refrigerator, freezer,
air tower, and dispenser cannot be changed by yourself. If the
lights do not illuminate when the refrigerator and/or freezer door is
opened, call for assistance or service. In the U.S.A., call
1-800-253-1301. In Canada, call 1-800-807-6777.
Light Styles:
The dispenser lights are LEDs that cannot be changed.
The interior lights vary by model.
� Some models have mini LEDs that cannot be changed.
� Some models have full-size LED bulbs that can be changed.
To order replacement 2.0 W LED bulbs, use part number
W10574850A, and for 3.6 W, use part number W10565137A,
or call 1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).
2.0 watts
NOTE: Some LED replacement bulbs are not recommended
for wet/damp environments. The refrigerator and freezer
compartments are considered to be wet/damp environments. If
using a brand of LED bulb other than the recommended
Whirlpool LED bulb, read and follow all instructions on the
replacement bulb's packaging before installing it.
� Some models have interior incandescent 40 W
bulbs that can be changed.
NOTE: Not all replacement bulbs will fit your
refrigerator. Do not use an incandescent bulb in
excess of 40 watts.
To Change a Light Bulb:
1. Unplug refrigerator or disconnect power.
2. Remove the light shield, as explained in the following
sections.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Before reinstalling, thoroughly rinse and dry
the shield.
4
3. Replace the burned-out light bulb, as explained in the
4. Reinstall the light shield, as explained in the following
5. Plug in refrigerator or reconnect power.
Refrigerator Compartment – Upper Lights
Light Shield Removal:
Slide the light shield toward the rear of the refrigerator and remove
it from the light housing.
Replacement Bulb:
� If the burned-out light is a full-size LED bulb, replace it with a
� If the burned-out light is an incandescent bulb, replace it with
Light Shield Reinstallation:
Align the light shield in the grooves at the bottom edge of the light
housing; then slide it forward until it snaps into place.
Refrigerator Compartment – Lower Lights
Light Shield Removal:
Slide the light shield to the right to remove the left end from the
wall slots; then pull the right end out of its wall slots.
3.6 watts
Replacement Bulb:
� If the burned-out light is a full-size LED bulb, replace it with a
� If the burned-out light is an incandescent bulb, replace it with
following sections.
sections.
2.0 W LED bulb.
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).
3.6 W LED bulb.
an incandescent appliance bulb of the same size, shape, and
wattage (40 W maximum).