1. Manuals
  2. Brands
  3. Sinocan Manuals
  4. Touch terminals
  5. Simple Shop ZJ-5801LD
  6. Manual

Sinocan Simple Shop ZJ-5801LD Manual

Mini usb, rs232, bluetooth prenosni pos
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Simple Shop ZJ-5801LD - Mini USB, RS232, Bluetooth prenosni POS
Introduction
Appreciate for purchasing our thermal receipt series printers. This manual is used on our mini
portable thermal receipt series printers.The manual will guide you to know all the functions and
operation solutions of our products.
All rights reserved. Reproduction of any part of this manual in any form whatsoever, without
manufacturer's express permission is forbidden.
Declaration
We have been carefully handling the manual and trying our best to
contents of this manual
improved and updated all the time. T
time.
All of our products must be used under environments/locations which are taken care by human
being. We are not responsible for any loss or damages caused by any accident while the products are
used without taken-care by human being. If there are any products failures caused by human
behaviors or natural disaster, we will not provide or just provide partial free maintenance.
Please contact local agents for the latest information of the products.
www.vse-za-blagajne.si
www.simple-shop.si
. But we still can't promise it is always correct due to our products are being
he contents of this manual will be updated without notice at any
-1-
---Version
1.0.0.4
ensure the accuracy of the

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Simple Shop ZJ-5801LD and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sinocan Simple Shop ZJ-5801LD

Summary of Contents for Sinocan Simple Shop ZJ-5801LD

  • Page 1 Simple Shop ZJ-5801LD - Mini USB, RS232, Bluetooth prenosni POS ---Version 1.0.0.4 www.vse-za-blagajne.si www.simple-shop.si Introduction Appreciate for purchasing our thermal receipt series printers. This manual is used on our mini portable thermal receipt series printers.The manual will guide you to know all the functions and operation solutions of our products.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 1. Description 1-1. Appearance 1-2. Specification& Features 1-3. Application area 1-4.Package and accessories ………………………………..……………………..…………………6 2. Communication Interface 2-1. RS-232 Serial Interface 2-2. Bluetooth Connection 2-2-1. Bluetooth specification 2-2-2. Use “AT” command to modify Printer’s parameters 2-2-3. Build connection 2-3.USB Interface 3.
  • Page 3 5-2. Notes on using 5-3. Notes on handling 5-4. Others 6. Programmer Manual...

  • Page 4: Description

    Description Mini Bluetooth Printer is a portable thermal printer that combines USB,RS-232 Serial and Bluetooth communication interface together, The printer could be powered by car charger, and rechargeable battery(depending on specified models) . These special characters make it successfully be applied to a variety of instruments, handheld data printing. 1-1.
  • Page 5 Overall Dimension (W×D× 105×75×45mm Weight 134g Color Dark gray Effective print width 48mm Print method Thermal line printing Print commands ESC/POS compatible command set Print speed Up to 90mm/sec Resolution 8 dots/mm(203dpi) Print font 12x24/24x24 Column capacity 32 columns/16columns Character size 1.5 x 3.0 mm(W x H)/ 3.0x3.0mm(WxH) Paper dimensions 58.0±0.1mm x diameter 40.0mm...

  • Page 6: Application Area

    1-3. Application area Compared to the traditional thermal receipt printer, Mini printer has smaller body, more reliable capability, more steady printing and portable advantages. The Mini printer can work on a lot of locations, such as the TAXI bill printing, administrative fees receipt printing, post receipt printing, restaurant ordering information printing, online payment information printing, etc.

  • Page 7: Communication Interface

    on different models(different interfaces) and customer requirement. Communication Interface 2-1. RS-232 Serial Interface RS-232 is developed according to the EIA standard asynchronous transmission, the specifications are as following: Ø Data transmission: serial interface Ø Synchronization: asynchronous Ø Signal Level: RS-232 level, logic 1:-5.4v, logic 0 : +5.4v Ø...

  • Page 8: Bluetooth Connection

    2-2. Bluetooth Connection Bluetooth is a proprietary open wireless technology standard for exchanging data over short distances (using short-wavelength radio transmissions in the ISM band from 2400–2480 MHz) from fixed and mobile devices, creating personal area networks (PANs) with high levels of security. 2-2-1.

  • Page 9: Build Connection

    For example, if you want to change baud rate to 115200bps, please send string “AT+BAUD8”. 2-2-3. Build connection. 1. Turn on the printer; 2. Search for the Bluetooth device with host device; 3. If there are other Bluetooth devices, please select “LY58”(for example) printer; 4.

  • Page 10: Basic Operation

    Basic Operation 3-1. indicator light & printer status There are Three indicators, they are red and blue 【CHARGE】 light, red 【ERROR】 light, and blue 【BATTERY】indicator. The meanings of each indicators are as below: 【CHARGE】indicator Blue light constant on: charging is completed; Red light constant on: in charging;...

  • Page 11: Selftest

    when loosen【FEED】 button. 3-2-4. Selftest User can check the printer’s current setting at anytime by printing Selftest page. Selftest printing method: Power off the printer, then hold down the【FEED】button and press the power button at the same time. Wait until the battery indicator &【ERROR】led is on ,then loosen the【FEED】button,the current setting will be printed out.

  • Page 12: Cleaning Of Printer

    computer. You could find <iprinter.exe> in our disk or download it from our website. The setting includes: set default code page, set default baud rate (only for serial interface), download NV logo. 3-3. Cleaning of printer When the printer has the following conditions, you should clean the printer head: Ø...

  • Page 13: Installing Wizard

    Installing Wizard Insta lling Wiza rd (Only for Bluetooth Interfa ce) Step1: Make sure your device (like PC, Note Book) has Bluetooth function, then once the Bluetooth for your device is activated, you will see the Bluetooth sign showed in the right bottom side of your device(like PC) screen. Step2: Power on the Bluetooth printer.
  • Page 14 Step4: if you can see screen as below,then the device is searching the bluetooth printer,please wait. -14-...
  • Page 15 Step5: Once the Bluetooth printer is found. You can see it listed on the screen, Here, for example,LY58 bluetooth printer is successfully found. Please click “-LY58” ,à click “Next” -15-...
  • Page 16 Step6: Choose “Let me choose my own passkey”, then enter “1234”(this is factory default passkey, if you want to change it, you have to inform us to set the new passkey for you in our factory before shipping),then click “Next”. -16-...
  • Page 17 Step7: if you can see the screen as below, that means the Bluetooth printer is already connected. Please notice the assigned COM ports ,then Click”Finish”. -17-...
  • Page 18 Step8: Now if you want to test if the printer is OK to print, you could use a com tool , and send printed data to Outgoing COM port( here, it is COM5). (Com tool setting is 9600,N,8,1.) Done. -18-...

  • Page 19: Operating Precautions

    Operating Precautions This section presents important information intended to ensure safety and effective use of the printer. Please read carefully. 5-1. Notes on safety Be sure to use the specified battery and power source provided by our company. Connection to an improper power source may cause fire , explosion or damage to the printer.
  • Page 20 Normal thermal paper can’t be kept too long, if you want to keep the receipt for a long period, please choose long term effective thermal paper. 5-4. Others Ø The printer is to be installed on a flat dry surface. Ø...
  • Page 21 Programmer Manual 6-1. COMMANDS 6-1-1. Command Notation [Name] The name of the command. [Format] The code sequence. [Range] Gives the allowable ranges for the arguments. [Description] Describes the command’s function. [Details] Describes the usage of the command in detail. [Notes] Provides important information on setting and using the printer command, if necessary.
  • Page 22 approximately 72.1 mm {576/203"} ③ T he length of the vertical direction in page mode: approximately 117.3 mm {1662/360"} (6) Printing area Printing range is set by the command. It must be printing area ≤ p rintable area. (7) Ignore The state in which all codes, including parameters, are read in and discarded, and nothing happens.
  • Page 23 [Name] Print and return to standard mode in page mode [Format] ASCII Decimal [Description] Prints the data in the print buffer collectively and returns to standard mode. [Details] · The buffer data is deleted after being printed. · The printing area set by ESC W is reset to the default setting. ·...
  • Page 24 n = 3: Transmit error status n = 4: Transmit paper roll sensor status [Details] · The status is transmitted whenever the data sequence of <10>H<04>H< n> (1 £ n £ 4) is received. Example: In ESC * m n d1...dk, d1=<10>H, d2=<04>H, d3=<01>H ·...
  • Page 25 n = 2: Off-line status Off/On Decimal Function Not used.Fixed to Off. Not used.Fixed to On. Cover is closed. Cover is open. Paper is not being fed by using the FEED button. Paper is beging fed by the FEED button. Not used.Fixed to On.
  • Page 26 Not used.Fixed to Off. [Reference] DLE ENQ, GS a, GS r n (*) DLE ENQ [Name] Real-time request to printer [Format] ASCII ENQ n Decimal 16 [Range] 1 £ n £ 2 [Description] Responds to a request from the host computer. n specifies the requests as follows: Request Recover from an error and restart printing from the line where the error occurred...
  • Page 27 [Name] Generate pulse at real-time [Format] ASCII Decimal 16 [Range] n = 1 m = 0, 1 1 £ t £ 8 [Description] Outputs the pulse specified by t to connector pin m as follows: Connector pin Drawer kick-out connector pin 2. Drawer kick-out connector pin 5.
  • Page 28 [Format] ASCII Decimal [Range] 0 ≤ n ≤ 255 [Description] Sets the character spacing for the right side of the character to [ n ´  h orizontal or vertical motion units]. • The right-side character spacing for double-width mode is twice the normal [Details] value.
  • Page 29 Underline mode not selected. Underline mode selected. • When both double-height and double-width modes are selected, quadruple size [Details] characters are printed. • The printer can underline all characters, but can not underline the space set by HT or 90° clockwise rotated characters. •...
  • Page 30 Decimal 0 ≤ nL ≤ 255 [Range] [Description] Selects or cancels the user-defined character set. • When the LSB of n is 0, the user-defined character set is canceled. • When the LSB of n is 1, the user-defined character set is selected. •...
  • Page 31 • When font B (9 ╳ 17) is selected. -31-...
  • Page 32 ESC * m nL nH d1... dk [Name] Select bit-image mode [Format] ASCII m nL nH d1...dk 2A m nL nH d1...dk Decimal 42 m nL nH d1...dk [Range] m = 0, 1, 32, 33 0 ≤ nL ≤ 255 0 ≤...
  • Page 33 • d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0 to not print a dot. • If the width of the printing area set by GS L and GS W less than the width required by the data sent with the ESC * command, the following will be performed on the line in question (but the printing cannot exceed the maximum printable area):...
  • Page 34 ESC – n [Name] Turn underline mode on/off [Format] ASCII Decimal 0 ≤ n ≤ 2, 48 ≤ n ≤ 50 [Range] [Description] Turns underline mode on or off, based on the following values of n : Function 0, 48 Turns off underline mode 1, 49 Turns on underline mode (1-dot thick)
  • Page 35 ESC 2 [Name] Select default line spacing [Format] ASCII Decimal [Description] Selects 1/ 6-inch line (approximately 4.23mm) spacing. •The line spacing can be set independently in standard mode and in page mode. [Details] [Reference] ESC 3 ESC 3 n [Name] Set line spacing [Format] ASCII...
  • Page 36 [Details] ·  W hen the printer is disabled, it ignores all data except for error-recovery commands (DLE EOT, DLE ENQ, DLE DC4) until it is enabled by this command. [Default] n = 1 ESC ? n [Name] Cancel user-defined characters [Format] ASCII Decimal...
  • Page 37 • This command cancels the previous horizontal tab settings. • When setting n = 8, the print position is moved to column 9 by sending HT. • Up to 32 tab positions ( k = 32) can be set. Data exceeding 32 tab positions is processed as normal data.
  • Page 38 Decimal 0 ≤ n≤ 255 [Range] Prints the data in the print buffer and feeds the paper [ n ╳ vertical or horizontal [Description] motion unit] inches. • After printing is completed, this command sets the print starting position to the [Details] beginning of the line.
  • Page 39 ⑤ S et printable area width: GS W • The following command is ignored in page mode: ① E xecute test print: GS ( A • The following command is not available in page mode: ① P rint NV bit image: FS p ②...
  • Page 40 Norway Denmark Spain Latin Korea Slovenia/Croatia Chinese The character sets for Slovenia/Croatia and China are ZJported only in the Simplified Chinese model. [Default] Simplified Chinese model: n = 15 Models other than the Simplified Chinese model: n = 0 ESC S (*) [Name] Select standard mode [Format]...
  • Page 41 48 £ n £ 51 [Description] Selects the print direction and starting position in page mode. n specifies the print direction and starting position as follows: Print Direction Starting Position 0, 48 Left to right Upper left 1, 49 Bottom to top Lower left 2, 50 Right to left...
  • Page 42 [Description] Turns 90° clockwise rotation mode on/off n is used as follows: Function 0, 48 Turns off 90° clockwise rotation mode 1, 49 Turns on 90° clockwise rotation mode [Details] · This command affects printing in standard mode. However, the setting is always effective.
  • Page 43 · The horizontal and vertical motion unit are specified by GS P. Changing the horizontal or vertical motion unit does not affect the current printing area. · The GS P command can change the horizontal (and vertical) motion unit. However, the value cannot be less than the minimum horizontal movement amount, and it must be in even units of minimum horizontal movement amount.
  • Page 44 nL+ nH ╳ 256 = N When pitch N is specified to the left (the negative direction), use the complement of 65536. When pitch N is specified to the left: nL+ nH ╳ 256 = 65536 - N • The print starting position moves from the current position to [ N ╳ h orizontal or vertical motion unit] •...
  • Page 45 [Name] Select paper sensor(s) to output paper end signals [Format] ASCII 63 33 Decimal 99 51 0 £ n £ 255 [Range] [Description] Selects the paper sensor(s) to output paper end signals · Each bit of n is used as follows: Off/On Decimal Function...
  • Page 46 Paper roll near-end sensor enabled Undefined [Details] · When a paper sensor is enabled with this command, printing is stopped only when the corresponding paper is selected for printing. · When a paper-end is detected by the paper roll sensor, the printer goes offline after printing stops.
  • Page 47 0 ≤ t1 ≤ 255, 0 ≤ t2 ≤ 255 [Description] Outputs the pulse specified by t1 and t2 to connector pin m as follows: Connector pin 0, 48 Drawer kick-out connector pin 2. 1, 49 Drawer kick-out connector pin 5. •...
  • Page 48 [Details] · Only the lowest bit of n is valid. · This command is enabled only when processed at the beginning of a line in standard mode. · When this command is input in page mode, the printer performs only internal flag operations.
  • Page 49 buffer. · In page mode, this command is not effective. · This command is not affected by print modes (emphasized, double-strike, underline,character size, white/black reverse printing, or 90° rotated characters, etc.), except upside-down printing mode. · If the printing area width set by GS L and GS W for the NV bit image is less than one vertical line, the following processing is performed only on the line in question.
  • Page 50 defined. In this case, all data needs to be sent again. · From the beginning of the processing of this command till the finish of hardware reset,mechanical operations (including initializing the position of the printer head when the cover is open, paper feeding by using the FEED button, etc.) cannot be performed.
  • Page 51 [Details] · Frequent write command execution may cause damage the NV memory. Therefore, it is recommended to write the NV memory 10 times or less a day. · The printer performs a hardware reset after the procedure to place the image into the NV memory.
  • Page 52 (1 £ vertical number of times £ 8, 1 £ horizontal number of times £ 8) [Description] Selects the character height using bits 0 to 2 and selects the character width using bits 4 to 7, as follows: Off/On Decimal Function Character height selection.
  • Page 53 · When characters are enlarged with different sizes on one line, all the characters on the line are aligned at the baseline. · The ESC ! command can also turn double-width and double-height modes on or off. However, the setting of the last received command is effective. [Default] n = 0 [Reference] ESC !
  • Page 54 x ≤ y ≤ 1536 0 ≤ d ≤ 255 [Description] Defines a downloaded bit image using the number of dots specified by x and y • x specifies the number of dots in the horizontal direction. • y specifies the number of dots in the vertical direction. •...
  • Page 55 • This command is ignored if a downloaded bit image has not been defined. [Details] • In standard mode, this command is effective only when there is no data in the print buffer. • This command has no effect in the print modes (emphasized, double-strike, underline, character size, or white/black reverse printing), except forupsidedownprinting mode.
  • Page 56 · When white/black reverse printing mode is on, it also applied to character spacing set by ESC SP. · This command does not affect bit image, user-defined bit image, bar code, HRI characters, and spacing skipped by HT, ESC $, and ESC \. ·...
  • Page 57 • The horizontal motion unit (x) is used for calculating the left margin. The calculated result is truncated to the minimum value of the mechanical pitch. [Default] nL = 0, nH = 0 [Reference] GS P, GS W GS P x y [Name] Set horizontal and vertical motion units [Format]...
  • Page 58 ①ASCII [Format] Decimal ②ASCII Decimal ① m = 1,49 [Range] ② m = 66, 0 ≤ n ≤ 255 [Description] Selects a mode for cutting paper and executes paper cutting. The value of m selects the mode as follows: Print mode 0, 1, 49 Partial cut (one point left uncut) Feeds paper (cutting position + [ n ╳...
  • Page 59 • The horizontal and vertical motion units are specified by GS P. Changing the horizontal and vertical motion units does not affect the current left margin. • The horizontal motion unit ( x) is used for calculating the printing area width. The calculated result is truncated to the minimum value of the mechanical pitch.
  • Page 60 complement of 65536. When pitch N is specified to the movement upward: nL + nH × 256 = 65536 - N • Any setting that exceeds the specified printing area is ignored. • This command function as follows, depending on the print starting position set by ESC When the starting position is set to the upper left or lower right of the printing, the vertical motion unit ( y ) is used.
  • Page 61 GS a n [Name] Enable/Disable Automatic Status Back (ASB) [Format] ASCII Decimal [Range] 0 £ n £255 [Description] Enables or disables ASB and specifies the status items to include, using n as follows: Off/On Decimal Status for ASB Drawer kick-out connector pin 3 status disabled.
  • Page 62 [Range] n = 0, 1, 48, 49 [Description] Selects a font for the HRI characters used when printing a bar code. n selects a font from the following table: Font 0, 48 Font A (12 × 24) 1, 49 Font B (9 × 17) [Details] .
  • Page 63 45, 46, 47 d = 42 1 ≤ k ≤255（even number） 48 ≤ d ≤ 57 48 ≤ d ≤ 57, 65 ≤ d ≤ 68, CODABAR 1 ≤ k ≤ 255 d = 36, 43, 45, 46, 47, 58 UPC-A 11 ≤...
  • Page 64 data as normal data. . If the horizontal size exceeds printing area, the printer only feeds the paper. . This command feeds as much paper as is required to print the bar code, regardless of line spacing specified by ESC 2 or ESC 3. .
  • Page 65 host is ready to receive data (DSR signal is SPACE). If the host computer is not ready to receive data (DSR signal is MARK), the printer waits until the host is ready. When XON/XOFF control is selected, the printer transmits only 1 byte without confirming the condition of the DSR signal.
  • Page 66 1, 49 Double-width 200 DPI 100 DPI 2, 50 Double-height 100 DPI 200 DPI 3, 51 Quadruple 100 DPI 100 DPI · xL, xH, select the number of data bits ( xL+ xH´256) in the horizontal direction for the bit image. ·...
  • Page 67 . Multi-level bar codes are as follows: UPC-A, UPC-E, JAN13 (EAN13), JAN8 (EAN8), CODE93, CODE128 . Binary-level bar codes are as follows: CODE39, ITF, CODABAR n = 3 [Default] [Reference] GS k FS ! n [Name] Set print mode(s) for Kanji characters [Format] ASCII Decimal...
  • Page 68 Decimal 28 [Description] Selects Kanji character mode. [Reference] FS ., FS C FS – n [Name] Turn underline mode on/off for Kanji characters [Format] ASCII Decimal [Range] 0 ≤ n ≤ 2, 48 ≤ n ≤ 50 [Description] Turns underline mode for Kanji characters on or off, based on the following values of n . Function 0, 48 Turns off underline mode for Kanji characters...
  • Page 69 Japanese Kanji ZJporting model c1 = 77H 21H ≤ c2 ≤ 7EH (JIS code system) ≤ d ≤ Japanese Kanji ZJporting model c1 = ECH 40H ≤ c2 ≤ 7EH (SHIFT-JIS code system) 80H ≤ c2 ≤ 9EH = 72 Chinese Kanji ZJporting model c1 = FEH A1H ≤...
  • Page 70 n 1 n2 n 1 n2 Decimal [Range] 0 ≤ n 1 ≤ 255 0 ≤ n 2 ≤ 255 Sets left- and right-side Kanji character spacing n1 and n2 , respectively. [Description] • When the printer model used ZJports GS P, the left-side character spacing is [ n1 ╳...

Table of Contents