Sealey 300TR Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. SAFETY
 WARNING! Ensure all preliminary checks are carefully carried out before use of jack. Immediately repair or replace damaged parts (use
authorised service agent). Ensure use of genuine parts only. Non authorised parts may be dangerous and will invalidate the warranty.
 WARNING! Use jack on level and solid ground, preferably concrete. Ensure the floor over which the jack will be transported is swept
clean.
▲ DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious personal or fatal injury may
result.
▲ DANGER! If jack tips or leans STOP what your are doing. MOVE QUICKLY TO A SAFE DISTANCE. DO NOT TRY TO HOLD OR
STEADY JACK. Serious personal or fatal injury may result.
 Use jack in an adequate working area for its function, keep area clean & tidy and free from unrelated materials. Ensure there is
adequate lighting.
 Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
 Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
 Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/or tie back long hair.
 WARNING! Ensure load is placed level and centrally on jack saddle and load is fixed in place before attempting to lift, lower, or
transport.
The lowering speed will vary according to the weight of the load and the release valve setting.

 Ensure the jack saddle is fully lowered and is clean, dry, and oil free before attempting to move the jack with or without a load.
 Diligence is required in ensuring that you continually monitor any operation until completed.
 WARNING! DO NOT operate jack if any parts are damaged or missing.
 DO NOT exceed the rated capacity of the jack.
 DO NOT allow untrained persons to operate the jack.
 DO NOT place any part of your body within or under the jack during use.
 DO NOT raise or lower vehicle lifting platform whilst the transmission jack is being used.
 DO NOT transport the jack, with or without a load, with the saddle in the raised position.
 DO NOT get jack wet or use in damp or wet locations or areas where there is condensation.
 DO NOT operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT lift or support vehicles with jack and DO NOT use jack as a load sustaining device.

 DO NOT use jack for any purpose other than removal, transportation, installation of transmissions.
 DO NOT move jack without suitable restraint on the load.
 DO NOT make any modifications to the jack, and DO NOT adjust or tamper with safety valve.
 DO NOT remove any labels from the jack. If labels are damaged or unclear replace them.
 Use a qualified person to lubricate and maintain the jack.
 DO NOT use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
 Before storing in safe area, ensure all parts are clean, free of grease and oil (especially saddle). Lower saddle to the lowest position.
2. INTRODUCTION
Manufactured to exacting standards, strong construction for durability and suitable for general workshop applications. Spring loaded dead
man's safety release control reduces the risk of inadvertent lowering. 2-Way hydraulic unit ensures that the saddle lowers at a controlled speed
at all times, even without load. Extra-large castors allow for increased manoeuvrability. Hydraulic unit larger than the economy models for
improved performance and durability. Can be fi tted with optional Adjustable Gearbox Support - check specifi cation in table.
© Jack Sealey Limited
VERTICAL TRANSMISSION JACK
300TR, 600TR
MODEL NO:
Original Language Version 300TR 600TR Issue 5 (HF) 22/11/21