Table of Contents
Advertisement
Quick Links
MODEL 545
INSTRUCTION MANUAL
DELUXE MAT CUTTING KIT
INSTRUCTIONS & OPERATION MANUAL
23 in (51 cm) capacity cutting board,
bevel cutter, straight cutting knife,
mat boards, blades, DVD, mat cutting book.
For best results use only
authentic Logan blades
Uses Logan Replacement
Blade #270
Mat border calculator
Mobile app
Purchase Date
ID Number (on bottom of board)
Date (on bottom of board)
L2125 6/12
LoganGraphic.com
Advertisement
Table of Contents
Related Manuals for Logan Graphic Products 545
Summary of Contents for Logan Graphic Products 545
- Page 1 MODEL 545 INSTRUCTION MANUAL DELUXE MAT CUTTING KIT INSTRUCTIONS & OPERATION MANUAL 23 in (51 cm) capacity cutting board, bevel cutter, straight cutting knife, mat boards, blades, DVD, mat cutting book. For best results use only authentic Logan blades Uses Logan Replacement...
-
Page 2: Identification Of Machine Components
Mounted 90 degree bars used to hold mats square when cutting and to set border sizes Blade Holding Knob (attach to base, as shown) Holds blade securely onto blade holder pg 2 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com... -
Page 3: Blade Installation
Remove blade knob. Slide blade down front of blade holder and into slot. (Fig. 2) Align hole in blade with hole in blade holder. Replace knob. pg 3 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com... - Page 4 Adjust setting by sliding blade nut to desired location and tighten. Helpful Hint - Second setting on knife is for 3/16 foamboard or double thick matboard Fig. 4 pg 4 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com...
- Page 5 Stand with squaring bars furthest from you, hold knife vertically along edge of guidebar at 45 degree angle. Place blade tip beyond edge of matboard. Draw knife across matboard towards yourself. (Fig. 6) pg 5 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com...
- Page 6 Align edge of matboard to desired dimension. (Fig.7 ) Using a pencil, draw lines full length of back of matboard. Repeat this for remaining three sides. pg 6 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com...
- Page 7 Remove blade from mat by pulling up on blade holder using your thumb. 10. Rotate the mat to 1/4 turn and repeat steps 6-9 to complete cutting. pg 7 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com...
-
Page 8: Helpful Hints
Always use a slip sheet when bevel cutting. A piece of scrap matboard used under mat being cut provides the highest quality cut. Change blades -When edge of cut looks ragged. Blade sharpness varies so blade life varies. Fig. 10 Blade Depth Blade Depth Screw pg 8 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com... -
Page 9: Troubleshooting
Change the blade. A dull blade will flare out causing a hook or curve. A NOTE ON BLADES: No two blades will have the same lifespan. Always start with a new blade before each project to ensure best results. pg 9 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com... -
Page 10: Warranty
Warranty Logan Graphic Products, Inc. (“Logan”) warrants the Deluxe Mat Cutting Kit Model 545 to be free from defects in parts and workmanship for a period of two years from the date of original purchase. Logan warrants that it will either repair or replace, in its sole discretion, any necessary replacement parts found to be defective.