Black & Decker BHFEB520D Manual page 8

Markings on Appliance
The following symbols appear on this appliance along with
the date code.
Read instruction manual before use.
Keep hair away from brushes, openings and other
moving parts.
BHFEB520D uses charger S010**2400040/ SSC-250040**.
Date Code Position (Fig. B)
The production date code
by a 2-digit week and is extended by a 2-digit factory code.
Features (Fig. A)
This tool includes some or all of the following features.
ON/OFF button
1
Variable power switch
2
Main handle
3
Floorhead ON/OFF button
4
Vacuum inlet
5
Charge port
6
Extension tube
7
Accessory release latch
8
Dust canister cap
9
Lift away dust canister
10
Floorhead
11
LED worklight
12
2 in 1 brush
13
Crevice tool
14
Pet hair tool
15
Battery pack
16
Battery release button
17
Charger plug
18
Cup Charger
19
Charging station
20
Retaining tabs
21
Charging station slots
22
Accessory storage clip
23
Assembly (Fig. F)

WARNING:
unit with the rear of the vacuum facing a wall so that any
inadvertent fall of the unit would contact a wall and not
people or pets.
1. Align the top of the extension tube
vacuum inlet 5 as shown in Fig. F.
2. Push the extension tube
locks into position.
3. Align the bottom of the extension tube
head as shown in Fig. F.
11
consists of a 4-digit year followed
33
When not in use position the
7 with the
7 onto the vacuum inlet
7 with the floor
4. Push the bottom of the extension tube
head 11
5. To remove an accessory, press the extension pole release
button 8
extension tube and gently pull the connected accessory off.
Inserting and Removing the Battery Pack
from the Tool (Fig. E)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. E).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Use (Fig. A, G–J)
This vacuum can be used in one of four ways.
With the extension tube
-
floorhead
- With the floorhead
- With the extension tube
accesssory tool
- With an accesssory tool
Switching ON and OFF (Fig. K)
1. To switch ON, push the ON/OFF button
2. For increased power, slide the
variable power switch
nOTE: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
3. To switch OFF, press the ON/OFF button
4. Return the product to the charger immediately after use so
that it will be fully charged and ready for the next use.
nOTE: Ensure that the product is fully engaged with the
charger plug.
Switching the Floorhead OFF and ON (Fig. K)
• To switch the floorhead OFF, press the Floorhead ON/OFF
button 4
• To switch the floorhead ON, press the floorhead ON/OFF
button 4
nOTE: The LED worklights
floorhead is switched ON.
Using an Accessory Tool (Fig. L)
Your vacuum may come with some of the following tools.
5 so it
Crevice tool.
-
- 2 in 1 brush
- Pet hair tool.
so it locks into position.
located on the vacuum inlet or the bottom of the
16
17
and the
7
11 . (Fig. G)
11 . (Fig. H)
7 and an
15 , 14 , 13 . (Fig. I)
15 , 14
forward.
2
.
a second time.
12 will illuminate whenever the
English
7 onto the floor
is fully charged.
and firmly pull the
, 13 . (Fig. J)
1 .
1 a second time.
7