Subscribe to Our Youtube Channel
Related Manuals for fine fixtures SES1
Summary of Contents for fine fixtures SES1
- Page 1 206 Wembly Road New Windsor, NY 12553 Phone: 718.602.6060 Fax: 718.963.2082 info@finefixtures.com www.finefixtures.com INSTALLATION MANUAL SHOWER ENCLOSURE SQUARE FRAMELESS MODELS: SES1-32 SES1-36 SES1-42 MODEL# SES1...
- Page 2 READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED, COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION. ATTENTION! PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT INSTALLATION OF THIS PRODUCT BY AN INEXPERIENCED INSTALLER MAY RESULT...
-
Page 3: Components And Hardware
PARTS COMPONENTS AND HARDWARE During unpacking the product and prior to installation inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged. Part Plastic Anchor Pieces Part Support Pieces... -
Page 4: Attaching The Base
ATTACHING THE BASE Attach the base to the floor of the shower area. (Professional install recommended) - Page 5 PREPARING THE FIRST FIXED GLASS PANEL Attach the plastic seal (D) to a side of the fixed glass panels (E, P), as shown. Attach the joints (C) to one side of the panel (over the seal), using screws included with the joints.
- Page 6 ATTACHING THE FIXED PANELS Use a pencil to mark the screw points in the wall, based on the location of the joints (C). Use a size 6 drill bit and insert the wall anchors (A) at the drilled points. Attach the joints to the wall with screws (F), using a screwdriver.
- Page 7 ATTACHING THE SUPPORT ARM support arm (B) Use a pencil to mark the screw points for the support arm (B) on the wall. Use a size 6 drill bit to drill holes at the marked points. Insert the wall anchors (A) into the holes in the wall.
- Page 8 ATTACHING THE DOOR HINGES Attach the door hinges (G) to the fixed glass (E) panel using screws included with the door hinges.
- Page 9 ATTACHING THE GLASS- TO-GLASS HINGE Use a pencil to mark the points where the screws for the bottom hinge (K) will be drilled. Use a size Ø6 drill bit to drill holes at the marked points to insert the screws. Inset plastic anchor (A) and attach the glass-to-glass bottom hinge (K) to the first fixed panel (E, P)
- Page 10 ATTACHING THE GLASS DOOR JOINTS Attach the door (N) to the joints of the fixed glass panel (E) using screws included with the joints. Affix plastic seals (I) to the bottom and lengths of the glass door (N). Affix plastic seals (O) to the bottom and lengths of the glass door (N) and fixed panel (P).
-
Page 11: Attaching The Door Handles
ATTACHING THE DOOR HANDLES Attach the shorter door handle (H) vertically to the outer side of the glass door using screws included with the handles. Attach the larger door handle (H) vertically to the inner side of the glass door using screws included with the handles. - Page 12 SECURING THE GLASS DOOR Secure the screws on the glass door with the Allen key. Note: The correct position of the door is shown below:...
-
Page 13: Completing The Assembly
COMPLETING THE ASSEMBLY Secure the seals, panels, and door with caulking gun and high-quality silicone or bathroom grade caulk. -
Page 14: After Installation
DRYING THE DOOR AND PANELS Leave the shower unused for 24 hours, so that it can dry completely. AFTER INSTALLATION WAIT 24 HRS BEFORE USE... - Page 16 F I N E F I X T U R E S 206 WEMBLY ROAD - NEW WINDSOR, NY 12553 P: 718.602.6060 F: 718.963.2082 - E: INFO@FINEFIXTURES.COM TOLL FREE: 1.877.8FIXTURES FINEFIXTURES.COM RETAIN THIS INSTALLATION MANUAL FOR FUTURE REFERENCE.
Need help?
Do you have a question about the SES1 and is the answer not in the manual?
Questions and answers