Related Manuals for KRAFTWERK RS1
Summary of Contents for KRAFTWERK RS1
- Page 1 Manual SpeedController- Soundcombo Wolfgang Haring e.U. Firmenbuchnummer: FN 312421 v (Landesgericht Wr. Neustadt) Kammanngasse 7-9A/8 A-2700 Wiener Neustadt Telefon +49 30 6098490 431 22.05.2023 www.kraftwerk.shop...
-
Page 2: Table Of Contents
We are very pleased that you have chosen one of our products. If you have any questions or suggestions, do not hesitate to send us an email to info@kraftwerk.shop or visit www.kraftwerk.shop, where you will always find the latest operating instructions, software and videos. -
Page 3: Product Description
Unlimited expandability The leading role of KraftwerK in the field of RC bus systems now comes into its own with the RS1. The RS1 can be expanded as required via the 6 EasyBus outputs. Lighting boards, switch extensions, servo controls and much more can be controlled via the EasyBus. -
Page 4: Factory Settings
6. I2C expansion port 7. Micro USB port 8. SD card, max. 32GB FAT32 formatted 9. Speaker connector, 4Ohm or more 10. Switching outputs 11. 10A switching outputs 12. Status LED 13. 4 expansion pins for plug-on modules 22.05.2023 www.kraftwerk.shop... -
Page 5: Technical Data
Play modes Touch, Loop, Once, Permanent, Random, Stoppoints Verwendbare Formate WAV, MP3 Verwendbare Abtastrate Alle (automatische Konvertierung nach 44.100) Volume control Poti, Poti, via channel, via software SD card max 32Gb, larger cards can be formatted to 32Gb 22.05.2023 www.kraftwerk.shop... -
Page 6: Commissioning
7. Commissioning The RS1 must be connected to five channels of the receiver. The use of a light and sound control pad can be configured using jumpers. 7.1. Upper jumper set, pad on K3 The engine brake is active if K2 is pressed up, provided the model sound supports this. -
Page 7: Upper Jumper Not Set, Control Via Button On K3
If K2 is pulled down and then tapped to the right, the horn is switched to horn and fanfare, provided the model sound supports this. If a button is used for K3, only the full-way functions can be switched. If necessary, half the functions can also be implemented using the appropriate mixer on the remote control. 22.05.2023 www.kraftwerk.shop... -
Page 8: Connecting The Receiver
7.3. Connecting the receiver Before you connect the RS1 to the receiver, you should check the channel assignments of your receiver. To do this, take a servo and check each output for correct function and note the assignment. Caution: it is advisable to jack up the model to prevent the model from moving off unintentionally. Then connect all servo cables to the corresponding outputs of the receiver. -
Page 9: Modellsounds
8. Modellsounds Sound Jumperstellung Last verfügbar Motorbremse verfügbar Scania 770S Volvo FH16 Mercedes Actros Unimog Mack Kenworth Benutzerdefiniert 22.05.2023 www.kraftwerk.shop... -
Page 10: Connection Plans
9. Connection plans The channels may vary depending on the remote control system. 22.05.2023 www.kraftwerk.shop... - Page 11 With the help of the live data view of the control panel, the assignment and the calibrating process can be checked. If an IBUS/SBUS/SUMD receiver is used, the assignment can also be changed using the live data view. The RS1 automatically switches to the protocol used. 22.05.2023 www.kraftwerk.shop...
-
Page 12: Appendix
12 Switching outputs Kraftwerk Licht Busnode 500mA per output Kraftwerk Servo Busnode 2 Servooutputs Kraftwerk Motor Busnode 1 Motor output 10 Ampere Types: Light, Servo, Motor Master/Busnode: The master contols the system, the busnodes have specialized tasks. 10.2. Terms ControlPanel The system can be configured with the free PC software ControlPanel.