Advertisement
Available languages
Available languages
1. Important information
Please read this manual completely and attentively before us-
ing the product for the first time. Keep this manual. It is part of
the product.
1.1 Safety instructions
Caution:
Risk of injury!
Due to the detailed reproduction of the original and the intend-
ed use, this product can have peaks, edges and breakable
parts. Tools are required for installation.
Electrical hazard!
Never put the connecting wires into a power socket!
Regularly examine the transformer for damage. In case of
any damage, do not use the transformer!
Make sure that the power supply is switched off when you
mount the device and connect the cables!
Only use VDE/EN tested special model train transformers
for the power supply!
The power sources must be protected to prevent the risk of
burning cables.
1.2 Using the product for its correct purpose
This product is intended:
-
For installation in model train layouts and dioramas.
-
For connection to an authorized model train transformer
(e. g. item 5200).
-
For operation in dry rooms only.
Using the product for any other purpose is not approved and is
considered inappropriate. The manufacturer is not responsible
for any damage resulting from the improper use of this product.
1.3 Checking the package contents
Check the contents of the package for completeness:
-
2 LEDs with connection cables
-
2 heat shrink tubes
-
2 lamp shades
-
2 lamp glasses
-
Lamp mast
-
Base socket
-
Resistor (multi-coloured rings)
-
Diode (single ring)
-
Manual
2. Introduction
This lamp produces light by SMD-LEDs which is suitable to the
lamp model. Low heat build-up and power input. Nearly unlimit-
ed lifetime of the LEDs, so no more change is required.
3. Assembly
- Remove the lamp kit carefully from the package.
1. Slide the two cable ends of the LEDs through the lamp mast
(fig. 3 steps 1 and 2).
2. Slide the base socket onto the cables (fig. 3 step 3).
3. Slide the lamp shade over the LEDs to the lamp mast (fig. 3
steps 4 and 5).
Afterwards the LED is placed in the lamp shade.
4. Put the lamp glass onto the lamp shade (fig. 3 steps 6 and 7).
5. Strip the yellow cable to ca. 2 cm. Bend the blank wire (ca. 1
cm) by 180° until it touches itself. Insert the wire bottom-up
through the lamp mast (fig. 4). The brass mast serves as a
second conductor. Twist the brown and the yellow wires below
the mast.
4
EN
6. Slide the yellow heat shrink piece onto both yellow cables
and the black heat shrink piece onto the brown cable (fig. 3
step 9).
7. Bend the short wire end of the resistor and the diode in the
middle by 90°. Wind the blank cable ends of the yellow ca-
bles around the wire directly below the resistor and the end
of the brown cable around the wire directly below the diode.
8. Afterwards bend the vertical end of the resistor and the diode.
9. Slide the heat shrink tube onto the previously made contact
point (cable + resistor or diode).
10. Heat it briefly (!), e. g. with a hot air gun and a durable
connection has been accomplished! Attention: Risk of burn!
4. Mounting
-
Check function before mounting.
-
Drill a hole (Ø 3.5 mm) at the mounting place (fig. 1).
-
Put the base socket with the cables from above through the
hole.
When connecting the cables, please leave a loop of ca. 2 – 3
cm behind the lamp, which enables you to pull the lamp out of
the assembly drilling.
Caution:
Resistor and diode at the cables are needed for proper func-
tion of the lamp. Never cover resistor or diode with insulation
material, because they have to be cooled by surrounding air!
5. Connection
Connect the LED lamp to the light output of a model train trans-
former (e. g. item 5200) as shown in fig. 4 and/or 5.
DC voltage: Connect the diode with the positive pole and the
resistor with the negative pole of the power supply.
AC voltage: Operation with AC voltage could cause some flick-
ering. We recommend to use the Viessmann power module,
item 5215 (fig. 5) which is sufficient for ca. 100 LED lamps or
reflectors. Connect the cable with the diode to the brown output
socket and the cable with the resistor to the red output socket
(fig. 4).
6. Technical data
Operating voltage:
(with and without item 5215 power module)
Operating current:
10 – 16 V AC ~
14 – 24 V DC =
13 – 24 V digital signal
ca. 10 mA
5
Advertisement
