Related Manuals for Agrify PRECISION HDU
Summary of Contents for Agrify PRECISION HDU
- Page 1 Model HDU – Hydrocarbon Distillation Unit Operational Manual Model HDU Operational Manual – For Hazardous Environments Precision® Extraction Solutions ©2022 PX2 Holdings, LLC. All rights reserved. Rev. 04/24/23...
- Page 2 Model HDU Operational Manual – For Hazardous Environments Congratulations on the purchase of your new Precision Extraction's ® Hydrocarbon Distillation Unit (HDU)! You are well on your way to a better experience in professional extraction. Please read and understand this operational manual thoroughly prior to using your new equipment.
-
Page 3: Table Of Contents
Model HDU Operational Manual – For Hazardous Environments Table of Contents SAFETY FIRST! SECTION 1 – PRODUCT OVERVIEW SECTION 2 – GETTING STARTED SECTION 3 – PRESSURE TESTING SECTION 4 – PREPARING FOR OPERATION SECTION 6 – CLEANING THE HDU SECTION 8 –... -
Page 4: Safety First
Model HDU Operational Manual – For Hazardous Environments SAFETY FIRST! SAVE THESE INSTRUCTIONS! It is the owners’ and operators’ responsibility to read and understand the following safety information. This equipment is to be installed, operated, maintained, cleaned, and transported only by trained, qualified personnel. Follow these safety precautions to ensure the safety of persons and property. -
Page 5: Section 1 - Product Overview
Model HDU Operational Manual – For Hazardous Environments Section 1 – Product Overview Figure 1: HDU Front View Injection Spool Heat Exchanger Filter Spool Lower Bowl Model HDU Operational Manual – For Hazardous Environments Precision® Extraction Solutions ©2022 PX2 Holdings, LLC. All rights reserved. Rev. 04/24/23... -
Page 6: Section 2 - Getting Started
Model HDU Operational Manual – For Hazardous Environments Section 2 – Getting Started Review the following system installation and operation requirements information before preparing for operation. Failure to do so may result in improper/unsafe installation and/or dangerous operating conditions. 2.1. System Placement 2.1.1. -
Page 7: Section 3 - Pressure Testing
Model HDU Operational Manual – For Hazardous Environments Section 3 – Pressure Testing The HDU comes factory tested and inspected for sustained pressure holding capabilities. However, shipping and moving of the unit may cause pressure leaks and/or equipment exposure to drastic changes in temperature. It is the operator’s responsibility to check for pressure leaks prior to operation. -
Page 8: Section 4 - Preparing For Operation
Model HDU Operational Manual – For Hazardous Environments Section 4 – Preparing and Operating the HDU Prior to use, the operator must read and be familiar with the specific operation manual of the extraction equipment. The following procedure outlines the steps to prepare operate the HDU. Nitrogen gas may be required to transfer solvent between vessels. This section is meant to be the baseline information for the operator to develop their internal SOP. -
Page 9: Section 6 - Cleaning The Hdu
Model HDU Operational Manual – For Hazardous Environments Section 5 – Cleaning the HDU The system can be internally cleaned without any disassembly by following the standard operation procedure for this unit. Clean solvent being transferred through the system will clean the surfaces and deposit any contaminants into the bottom bowl. In the event of each component needing to be cleaned individually, adhere to the following protocols. -
Page 10: Section 8 - Periodic Maintenance
Model HDU Operational Manual – For Hazardous Environments Section 6 – Periodic Maintenance Periodic maintenance is essential to the safe and proper operation of your equipment. Contact Precision® Extraction Solutions directly for replacement components. Obtaining replacement components from a third party voids your warranty and invalidates the engineering peer review of the equipment. -
Page 11: Appendix A - Facility Requirements
Model HDU Operational Manual – For Hazardous Environments Appendix A - Facility Requirements The system can be internally cleaned without any disassembly by following the standard operation procedure for this unit. Clean solvent being transferred through the system will clean the surfaces and deposit any contaminants into the bottom bowl. In the event of each component needing to be cleaned individually, adhere to the following protocols. -
Page 12: Appendix B - Assembly Requirements
Model HDU Operational Manual – For Hazardous Environments Appendix B - Assembly Requirements To ensure the sanitary clamps and gaskets are properly sealed, the bolts/nuts must be properly torqued. Always torque sanitary clamps to the material manufacturer’s specifications listed below. Never overtighten. Clamp Size Part Number Manufacturer Torque Spec.
Need help?
Do you have a question about the PRECISION HDU and is the answer not in the manual?
Questions and answers