LEEGOL ELECTRIC ZE-LG-490A User Instruction Manual
  1. Manuals
  2. Brands
  3. LEEGOL ELECTRIC Manuals
  4. Saw
  5. ZE-LG-490A
  6. User instruction manual

LEEGOL ELECTRIC ZE-LG-490A User Instruction Manual

8" bridge tile saw with stand
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER INSTRUCTION MANUAL
REV. 000
8" BRIDGE TILE SAW
WITH STAND
MODEL#: ZE-LG-490A
Save This Manual
Keep this manual for the sagety warnings and precautions assembly,
operating, inspection maintenance and cleaning procedures. Write the product's
serial nmber in the back of the manual near the assembly diagram
(or Month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference)
WARNING
Read this material before using this product. Failure to do so can result
in serious injury.
in serious injury.
SAVE THIS MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZE-LG-490A and is the answer not in the manual?

Questions and answers

Related Manuals for LEEGOL ELECTRIC ZE-LG-490A

Summary of Contents for LEEGOL ELECTRIC ZE-LG-490A

  • Page 1 USER INSTRUCTION MANUAL REV. 000 8" BRIDGE TILE SAW WITH STAND MODEL#: ZE-LG-490A Save This Manual Keep this manual for the sagety warnings and precautions assembly, operating, inspection maintenance and cleaning procedures. Write the product's serial nmber in the back of the manual near the assembly diagram (or Month and year of purchase if product has no number).

  • Page 2: General Safety Rules

    GENERAL SAFETY RULES READ THIS OWNER'S MANUAL COMPLETELTY AND MAKE SURE YOU UNDERSTAND ALL OF IT'S SAFETY GUIDELINES. 1. READ and become familiar with this owner's manual. Learn the limitations of the bridges saw and become aware of its possible hazards. 2.

  • Page 3: Specific Safety Rules

    18. NEVER STAND ON THE SAW. Serious injury could occur if the saw is tipped or if the cutting blade is unintentionally contacted. 19. CHECK DAMAGED PARTS. Before further use of the saw, the safety guard or any other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended funtion.
  • Page 4 in the Sketch A of Figure 1. A temporary adapter, which looks kike the adapter illustrated in Sketch B and C, may be used to connect to this plug to 2-pole receptacle as shown is Sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly ground outlet can be installed by a qualified electrician.
  • Page 5 C EXTENSION CORDS 1. Use only extension cords that are internded for outdoor use. These extension cores are indentified by a making " Acceptable for use with outdoor applicances, store indoors while not in use". Use only recommended extension cords. Do not use damaged extension cords. Examine extension cord before using and replace if damaged.

  • Page 6: Functional Description And Operation

    13. Never allow the blade to run dry. Failure to keep the water tray at the recommended level will in possible over-hearing of the diamond blade. SPECIAL SAFETY INSTRUCTIONS BEFORE USING BRIDGE SAW Checking the following areas: 1. Does the voltage motor correspond to the main voltage? 2.
  • Page 7 ASSEMBLY Read the manual carefully before assembly. 1. Clean the working area. 2. Remove saw from carton, you will find it assembled. 3. Lay the saw on its side on the ground (Fig 4) 4. Pull our the stand legs and support brackets (Fig5-1). Effort to promote support of the tripod was linear (Fig5-2), and withholding support for the security lock in place (Fig5-3).
  • Page 8 Figure 6-1 Figure 7 Mounting the Wheels (Fig 8) 1. Loosen the wing nuts on the folder legs. 2. Insert the wheels in place at the screws on the folder legs. 3. Fix the wheels using the wing nuts. 4. Put the "U" handle into the 2 holes on the folder legs, and tight the screws in the poles. 5.
  • Page 9 FILLING THE WATER AND DRAINING 1. Fill the tray with water. Do not add chemicals or detergents to the water. 2. Remove the plug from the bottom of the tray, the water will flow out or you can remove the tray and pour the water out.
  • Page 10 Figure 12 Figure 13 CHANGE THE BLADE WARING! Disconnect the power supply before making adjustments, maintenance, cleaning or replacing the blade! 1. CHOICE OF THE SAW BLADE. Only use 8 inch Continuous Rim or Turbo Blades with a 5/8 arbor. 2.

  • Page 11: Specifications

    PUMP REPLACING INSTRUCITON 1. Take the pump out of the Water Tray. 2. Take the pump out of the Protection Chain. 3. Open the Switch Box, and undo the Connecting Terminal, take the pump out of the Switch Box; 4. Then replace the old pump with a new pump. 5.

  • Page 12: Troubleshooting

    TROUBLESHOOTING Follow all safety prcautions whenever diagnosing or serving the Bridge Saw! Disconnect power supply before service Problem Possible Cause Likely Solutions *No power at outlet 1. Check power outlet The saw not start 2. Check the cord is plugged in. *Power cord not connected *Switch damaged 3.
  • Page 14 Machines Parts List No.: Parts Name Q’ty Plastic Chain Protection 1 set Al Guide 1 set Switch Box 1 set Capacitor 1 set Switch 1 pc Pull Handle 1 set Cutting Assisting Plate 1 set Water Tray Outlet 1 set Water Tray 1 set M8 Knobs...
  • Page 16 Foldable Legs Parts List No.: Part Name Q’ty Foldable Legs Components 1 set Limitors component 2 sets Handles 2 sets Small Knobs 2 sets Locking Plate 2 sets Feet Wheels 2 sets Pull Pole 1 set...

Table of Contents