1. Manuals
  2. Brands
  3. 3M Manuals
  4. Label Maker
  5. Matic Accuglide 2+
  6. Instructions and parts list

3M Matic Accuglide 2+ Instructions And Parts List

Upper and lower standard taping heads 3 inch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions and Parts List
3M-Matic
Type 10500
Upper and Lower
Standard Taping Heads
3 Inch
Serial #:
Important Safety Information
BEFORE INSTALLING OR OPERATING THIS EQUIPMENT
Read, understand and follow all safety and operating instructions.
Spare Parts
It is recommended you immediately order the spare parts listed in the "Spare
Parts/Service Information" section. These parts are expected to wear through
normal use, and should be kept on hand to minimize production delays.
™
3M-Matic
Accuglide 2+ - 3 Inch Taping Head
Page i
Accuglide
™
For reference, record machine serial number here.
2+
™
NA - ENG
April 2017

Advertisement

Table of Contents
loading

Related Manuals for 3M Matic Accuglide 2+

Summary of Contents for 3M Matic Accuglide 2+

  • Page 1 Instructions and Parts List 3M-Matic Accuglide ™ ™ Type 10500 Upper and Lower Standard Taping Heads 3 Inch Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
  • Page 2 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page ii...

  • Page 3: Replacement Parts And Service Information

    Replacement Parts and Service Information To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. ™ ™ ® It has been set up and tested in the factory with Scotch Tapes. ® Included with each machine is an Instructions and Parts List manual.
  • Page 4 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page iv...
  • Page 5 Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set up ™ ™ ® and tested in the factory with Scotch tapes. ® Included with each machine is an Instructions and Parts List Manual.
  • Page 6 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page vi...

  • Page 7: Table Of Contents

    Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™...

  • Page 8: Equipment Warranty And Limited Remedy

    3M to its factory or other authorized service station designated by 3M. If 3M is unable to repair or replace the part within a reasonable time after receipt thereof, 3M, at its option, will replace the equipment or refund the purchase price.

  • Page 9: Intended Use

    ® bottom center seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™...
  • Page 10 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 2...

  • Page 11: Taping Head Contents / How To Use Manual

    (ELV), a glossary with a defi nition of symbols, plus a parts list of the 3M-Matic™ Accugllide 2+ (3 inch) 3M Industrial Adhesives and Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) Edition April 2017/ Copyright 3M 2017.

  • Page 12: Important Safeguards

    The blades are extremely sharp. system is running (Important Safeguards continued on next page) NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 4...
  • Page 13 See "Replacement Parts Illustrations and Parts Lists" for label part numbers. 78-8133-9606-2 Tape Threading Label (Not shown) Figure 1-1 Replacement Labels/3M Part Numbers NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™...

  • Page 14: Specifi Cations

    90mm [3-1/2 inches] (with optional 2 inch leg length) Case Sealer Width – 150mm [6 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifi cations for box weight and size capacities.

  • Page 15: Dimensional Drawing

    [10-15/16 in.] [2 9/32 in.] 405 mm 18 mm [11/16 in.] 18 mm [11/16 in.] 445 mm [17-1/2 in.] 405 mm Figure 2-1 Dimensional Drawing NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 7...

  • Page 16: Installation

    Taping Head is supplied with a buffi ng the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.

  • Page 17: Operation

    Spring One-Way Tension Roller Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side View) NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 9...

  • Page 18: Tape Loading - Upper Taping Head

    2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 10...
  • Page 19 Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 11...

  • Page 20: Maintenance

    Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 12...

  • Page 21: Cleaning

    Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See Figure 4-2. NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 13...

  • Page 22: Adjustments

    - Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 14...

  • Page 23: Applying Mechanism Spring

    - Never attempt to work on the taping Figure 5-5 One-Way Tension Roller head or load tape while the box drive system is running (Adjustments continued on next page.) NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 15...

  • Page 24: Tape Leg Length

    - Keep hands and fi ngers away from tape Position B-B Extension cutoff blades under orange blade guards. Figure 5-7 Changing Tape Leg Length The blades are extremely sharp. NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 16...

  • Page 25: Troubleshooting Guide

    Make sure one-way bearing is contacting the taping head frame below the surface of the tension roller. If not, press bearing further into roller or replace roller. NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 17...
  • Page 26 Tape not centered on box seam Centering guides not centered Adjust centering guides Box fl aps not of equal length Check box specifi cations NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 18...

  • Page 27: Spare Parts/Service Information

    Roller – Buffi ng 78-8113-7030-9 Spring – Torsion Replacement Parts and Service Refer to the fi rst page of this instruction manual “Replacement Parts and Service Information". NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 19...
  • Page 28 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 20...

  • Page 29: Replacement Parts Illustrations And Parts List

    Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confi rm item availability. NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™...
  • Page 30 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 22...
  • Page 31 Figure 10400 (Lower) Figure 10396 Figure 10394 Figure 10388 (Upper) Figure 10390 (Lower) Figure 10392 ™ Taping Head Assemblies - AccuGlide 2+ STD 3 Inch NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 23...
  • Page 32 ™ AccuGlide 2+ - 3” 17 18 Figure 10398 – Upper Head NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 24...
  • Page 33 ™ AccuGlide 2+ - 3” Figure 10398 – Upper Head Ref. No. 3M Part No. Description 10398-1 78-8133-9456-2 Frame – Tape Mount Upper Assembly 10398-2 78-8133-9458-8 Frame – Front Upper Assembly 10398-3 78-8068-4143-9 Guide – #1 10398-4 78-8068-4144-7 Guide – #2...
  • Page 34 AccuGlide ™ 2+ - 3” Figure 10394 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 26...
  • Page 35 ™ AccuGlide 2+ - 3” Figure 10394 – Upper and Lower Heads Ref. No. 3M Part No. Description 10394 -1 78-8133-9520-5 Arm – Applying, R/H 10394-2 78-8133-9521-3 Arm – Applying, L/H 10394-3 78-8070-1292-3 Plate – Back-Up 10394-4 78-8076-4736-3 Shaft Roller...
  • Page 36 AccuGlide ™ 2+ - 3” Figure 10388 – Upper Head NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 28...
  • Page 37 ™ AccuGlide 2+ - 3” Figure 10388 – Upper Head Ref. No. 3M Part No. Description 10388-1 78-8070-1392-1 Buffi ng Arm – Sub Assembly 10388-2 78-8070-1391-3 Buffi ng Arm – Sub Assembly 10388-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon...
  • Page 38 AccuGlide ™ 2+ - 3” Figure 10396 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 30...
  • Page 39 ™ AccuGlide 2+ - 3” Figure 10396 – Upper and Lower Heads Ref. No. 3M Part No. Description 10396-1 78-8070-1388-9 Link – Arm Bushing Assembly 10396-2 78-8070-1389-7 Link – Arm Bushing Assembly 10396-3 78-8076-4740-5 Shaft – Pivot 10396-4 78-8017-9082-1 Bearing – Special 30mm...
  • Page 40 AccuGlide ™ 2+ - 3” Figure 10392 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 32...
  • Page 41 ™ AccuGlide 2+ - 3” Figure 10392 – 3" Upper and Lower Heads Ref. No. 3M Part No. Description 10392-1 78-8070-1283-2 Frame – Cut-Off 10392-2 78-8028-7899-7 Knife – 89mm/3.5 Inch 10392-3 26-1002-5817-2 Screw – Hex Hd, M5 x 8 10392-4 78-8076-4741-3 Knife Guard Assembly –...
  • Page 42 AccuGlide ™ 2+ - 3” Figure 10402 – Upper and Lower Heads NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 34...
  • Page 43 ™ AccuGlide 2+ - 3” Figure 10402 – 3" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10402-1 78-8070-1395-4 Bracket – Bushing Assembly 10402-2 78-8060-8462-6 Shaft – Tape Drum, 3 Inch Head 10402-3 78-8017-9169-6 Nut – M18 x 1...
  • Page 44 AccuGlide ™ 2+ - 3” 19 17 18 17 Figure 10400 – Lower Head NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 36...
  • Page 45 ™ AccuGlide 2+ - 3” Figure 10400 – Lower Head Ref. No. 3M Part No. Description 10400-1 78-8133-9502-3 Frame – Tape Mount Lower Assembly 10400-2 78-8133-9500-7 Frame – Front Lower Assembly 10400-3 78-8068-4144-7 Guide – #2 10400-4 78-8068-4143-9 Guide – #1...
  • Page 46 AccuGlide ™ 2+ - 3” Figure 10390 – Lower Head NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 38...
  • Page 47 AccuGlide ™ 2+ - 3” Figure 10390 – Lower Head Ref. No. 3M Part No. Description 10390-1 78-8070-1391-3 Buffi ng Arm Sub Assembly 10390-2 78-8070-1392-1 Buffi ng Arm Sub Assembly 10390-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 10390-5 78-8137-1397-7 Roller –...
  • Page 48 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 40...
  • Page 49 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 41...
  • Page 50 NA - ENG 3M-Matic Accuglide 2+ - 3 Inch Taping Head ™ April 2017 Page 42...

This manual is also suitable for:

10500

Table of Contents