Page 2
(hereinafter referred to as "product") are the results of targeted development and meticulous research. As of the date of delivery, burster provides a warranty for the proper condition and functioning of these products covering material and production defects for the period specified in the warranty document accompanying the product.
Note This indicates precautions which should be observed to ensure proper handling of the equipment - 7 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Use torque sensor only in non-safety-critical applications. Only use torque sensor outside of potentially explosive areas (Ex protected areas) - 8 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Page 9
Make sure that such peaks do not occur, or ensure that they are absorbed. - 9 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
The torque sensor is not intended for use as a safety device. Personnel Personnel must be familiar with the respectively applicable regulations. They must follow these regulations. - 10 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
You will see these markings on the measurement end of the sensor: fig. 1.: Sensor Test side - 11 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Page 12
(looking at the measurement end), you will get a negative signal at the output. fig. 4.: Torque, anti clockwise (looking at the measurement end) - 12 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Page 13
For more information on estimating the resonant frequency and measuring dynamic torques, see the section 7.3 "Dynamic torques" on page 34. - 13 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Only store the sensor under the following conditions: dry no Condensation Temperatures between 0° C and 60° C - 14 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
This microprocessor controls a digital/analog converter which generates an analog voltage again (16-bit - 16 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Page 17
360 / (4 x 1024) = 0.09°. For more information on the sign convention, see section 2.5 "Definitions" on page 11. - 17 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Support the sensor when fitting it. Do not drop the sensor. Do NOT use hammers during installation - 19 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...
Page 20
This avoids any unnecessarily high reaction forces, while also reducing the load on the coupling and any spurious forces acting on the sensor. - 20 / 83 - burster präzisionsmesstechnik gmbh &co kg ■ Talstr. 1-5 ■ 76593 Gernsbach ■ Tel.: (+49) 07224-6450 ■ www.burster.de ■ info@burster.com...