Advertisement
2
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is fl ashing, go to the next step 2.
2. Press
or
: adjust the time.
3. Press
: Set the time.
Remote Control Reset
Push
by tip of the pencil or
1. Remove the battery.
2. Press
.
3. Insert the battery.
3
AIRFLOW DIRECTION
Press
: Move the louver in
1
the desired vertical direction.
Press
: Swing the air
2
automatically and press again to stop.
For horizontal direction, adjust
3
manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
4
REMOTE CONTROL
1
Infrared signal emitter
2
Start/Stop button (
)
3
Mode select button (
)
4
Temperature button (
)
5
Fan speed button (
)
6
Swing louver button (
)
7
Set louver button (
)
8
On timer button (
)
9
Off timer button (
)
!
ECO Sleep button (
)
"
Setup button (
)
#
Clear button (
)
$
Memory and Preset button (
)
%
High power button (
)
&
Economy button (
)
(
Quiet button (
)
)
Filter reset button (
)
~
Set clock button (
)
+
Check button (
)
,
Reset button (
)
Note:
• The provided Remote Controller is a wireless type, which also can be used as
a wire. Please see "How to Connect The Remote Controller for Wired
Operation", located in installation instruction, in case of wired control is required.
• In wire operation, remote controller will return to initial condition (PRESET,
TIMER and CLOCK will return to initial condition) when user shutdown power
supply of Air conditioner.
1
$
4
6
2
5
7
3
(
&
%
#
8
9
!
"
+
,
~
)
5
AUTOMATIC OPERATION
To automatically select cooling or fan only operation
1. Press
: Select A.
2. Press
: Set the desired temperature.
3. Press
: Select AUTO, LOW , LOW+
or HIGH
.
6
COOLING / FAN ONLY OPERATION
1. Press
: Select Cool
or Fan only
2. Press
: Set the desired temperature.
Cooling: Min. 17
o
C, Fan Only: No temperature indication
3. Press
: Select AUTO, LOW , LOW+
or HIGH
.
7
DRY OPERATION
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press
: Select Dry
.
2. Press
: Set the desired temperature.
8
Hi-POWER OPERATION
To automatically control room temperature and airfl ow for faster cooling operation
(except in DRY and FAN ONLY mode)
Press
: Start and stop the operation.
9
ECO OPERATION
To automatically control room to save energy (except in DRY and FAN ONLY
mode)
Press
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1 degree/
hour for 2 hours (maximum 2 degrees increase).
10
TEMPORARY OPERATION
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 25°C and fan operation is
automatic speed.
11
TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting ON Timer
Press
: Set the desired ON
1
timer.
2
Press
: Set the timer.
Press
: Cancel the timer.
3
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Everyday Timer
Press
: Set the ON timer.
1
Press
: Set the OFF
2
timer.
• During the every day timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
, MED
, MED+
,
.
, MED
, MED+
,
Setting OFF Timer
Press
: Set the desired OFF
timer.
Press
: Set the timer.
Press
: Cancel the timer.
3
Press
.
Press
button during the
4
( or ) mark fl ashing.
EN
Advertisement
