Page 1
TECHNICAL INFORMATION MANUAL Revision 1 – 03/04/2023 R3101C R3104C Lepton Lepton 25dBm 1-Port RAIN 25dBm 4-Port RAIN RFID Reader Module RFID Reader Module...
Page 2
The information contained herein has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. CAEN RFID reserves the right to modify its products specifications without giving any notice; for up to date information please visit www.caenrfid.com.
Page 3
Disposal of the product Do not dispose the product in municipal or household waste. Please check your local regulations for disposal/recycle of electronic products.
Page 4
Index Scope of the Manual .................................2 Change Document Record ...............................2 Reference Document ................................2 Introduction ..................................6 Description ....................................6 Readers ..................................6 Evaluation Board ................................7 Ordering Options ..................................7 Technical Specifications ..............................8 Technical Specifications ................................8 Key Features ....................................9 Hardware Interface............................... 10 Introduction .....................................10 Power Supply ...................................11 RF Connection ..................................11 UART Communication ................................11...
Fig. 1.2: Lepton x4 (Model R3104C) Reader – top view Evaluation Board Mod. R4320CEVB - Evaluation Board allows managing the Lepton x1 and Lepton x4 readers directly using an USB interface (via the embedded USB to UART converter). This board is particularly suited for Lepton x1 and Lepton x4 readers evaluation and SW development purpose.
Lepton x4 system-level block diagram for an embedded system is shown in Fig. 3.1: Lepton3x1 R3101C/Lepton3x4 R3104C - Example of Block Diagram. This figure shows the electrical connections that may and must be made to control the R3101C Lepton x1/R3104C Lepton x4.
Fig. 3.2: BSL Sequence The BSL program execution starts when TST pin has received a minimum of two positive transitions and if TST is high while /RST rises from low to high. BSL_SEL shall be at high level before BSL starts. Pulses length and distance between edges of all signals shall be 10ms at least.
Page 12
Reset Pin The R3101C Lepton x1/R3104C Lepton x4 may be reset by a logic low voltage on the NRST pin (pin 14). Usage of this pin is recommended in all designs. It may be used to reset the part if an unexpected operating state is entered.
External Connections and Mechanical Drawings The location of the connectors is shown in Fig. 3.3: R3101C Lepton3x1 mechanical drawings and connectors locations (units: mm) and Fig. 3.4: R3104C Lepton3x4 mechanical drawings and connector locations (units: mm). Their part numbers are listed here below:...
Pin # Name Direction Function Ground Ground VDC_IN Supply voltage VDC_IN Supply voltage GPIO0 IN/OUT General purpose I/O #0 GPIO1 IN/OUT General purpose I/O #1 GPIO2 IN/OUT General purpose I/O #2 GPIO3 IN/OUT General purpose I/O #3 UART RX (input to the module) UART TX (output from the module) WKUP - RFU IN/OUT...
Tab. 3.4: Supply Current Specifications UHF Gen 2 RFID Radio Specifications Parameter Min. Typ. Max. Unit Conditions See § Tab. 2.1: Lepton3x1 - Lepton3x4 Technical Frequency Specifications page 8 865.6 867.6 Input impedance Ω Input match 10%PER, assuming 20 dB antenna RL @ 25 dBm...
Device Input and Output Specifications Parameter Min. Typ. Max. Unit Conditions nRST -0.3 Hysteresis voltage Internal pull-up resistor kΩ Reset pulse width μs Digital inputs -0.3 Hysteresis voltage Internal pull-down resistor kΩ Digital outputs Drive current (sink or source) UART Default baud rate 921.6 kbaud...
4 EVALUATION BOARD Technical Specifications Table Four I/O lines 3.3 V out @ 3mA, 5 V tolerant Digital I/O USB micro female connector Baudrate: 115200 Databits: 8 Stopbits: 1 UART via USB Port Parity: none Flow control: none 9.6÷115 kbit/s data rate (settable) It appears as USB serial port;...
Installation Notice Fix the R3101C Lepton x1/R3104C Lepton x4 reader to the R4320CEVB board using 3 M2x12 countersunk screws and 3 M2 screws nuts and connect the Molex connectors. The reader case shall be kept electrically isolated via thermal sildpad from the ground plane. The correct way to connect the R3101C Lepton x1/R3104C Lepton x4 module to the R4320CEVB...
Fig. 4.6: Connection of the R3104C module to the R4320CEVB evaluation board EVALUATION BOARD - Lepton x1 - Lepton x4 - Technical Information Manual...
Page 22
Connecting to the R3101C Lepton x1/R3104C Lepton reader USB Communication Setup Warning: If your PC is running a Windows version older than Windows 10, to correctly operate with the reader, you need to install the FTDI USB driver. You can find it easily via a WEB research. Evaluation Board USB-UART Details R4320CEVB board embeds an FTDI FT232BL UART to USB converter.
Page 23
On the main screen click on File → Connect. A Connection window will open. Select the Connection Type (RS232) and specify the RS232 port (COM 9 in this example). In order to connect to the module via Easy Controller software the serial settings shall be added to the COM port address since R3101C Lepton x1/R3104C Lepton x4 module has a different baudrate (921600bps) from default value used...
Page 24
Place one or more tags near the antenna connected to the reader, click on Start Inventory and see tags information displayed on the main window: For more information on the CAEN RFID Easy Controller for Windows application usage, please refer to the relevant user manual: you can download it from the...
Electrical Schematic The electrical schematic of the R4320CEVB is shown in the following figure: Fig. 4.8: R4320CEVB Electrical Schematic EVALUATION BOARD - Lepton x1 - Lepton x4 - Technical Information Manual...
External Connections Please refer to Fig. 4.7: R4320CEVB Technical Drawing page 25. J1: Power Supply connector: central pin (2.1mm diam.) is the negative terminal. The use of the Power Supply for R4320CEVB (WALIM0000005) is recommended (see § Ordering Options page 7). J2: header for GPIO external connection −...
SW3: Shall be used to correctly select communication interface of R3101C Lepton x1/R3104C Lepton module with the host: SW open to be used when UART interface is used directly connected to external device (i.e. microcontroller inside customer’s board) SW closed to be used when UART via USB interface is used (connection to PC via J4 connector) Fig.
Page 29
LEDs Please refer to Fig. 4.7: R4320CEVB Technical Drawing page 25. DL1 (green) = Power Supply DL2 (green) = not supported DL3 (green) = UART via USB connection DL4 (green) = GPIO0 DL5 (green) = GPIO1 DL6 (green) = GPIO2 DL7 (green) = GPIO3 DL8 (yellow) = UART via USB communication activity EVALUATION BOARD - Lepton...
Page 30
5 REGULATORY COMPLIANCE CE Compliance (mod. R3101C) Reference standard: ETSI EN 301 489-1 V2.2.3:2019 ETSI EN 301 489-3 V2.1.1:2017 ETSI EN 302 208 V3.3.1:2020 IEC 62368-1:2018 See § Lepton x1 R3101C CE DECLARATION OF CONFORMITY page 32 for the Lepton x1 R3101C CE Compliance Certificate.
Page 31
UKCA Compliance (mod. R3101C) Reference standard: ETSI EN 301 489-1 V2.2.3:2019 ETSI EN 301 489-3 V2.1.1:2017 ETSI EN 302 208 V3.3.1:2020 BS EN 62368-1:2014+A11:2017 See § Lepton x1 R3101C UKCA DECLARATION OF CONFORMITY page 34 for the Lepton x1 R3101C UKCA Compliance Certificate.
Page 32
R3101C LEPTON CE DECLARATION OF CONFORMITY CAEN RFID Srl Via Vetraia, 11 55049 Viareggio (LU) Italy Tel.: +39.0584.388.398 Fax: +39.0584.388.959 Mail: info@caenrfid.com Web site: www.caenrfid.com herewith declare under our own responsibility that the product: WR3101CXAAAA – Lepton x1 - 25dBm Reader Module corresponds in the submitted version to the following standards: ETSI EN 301 489-1 V2.2.3:2019...
Page 33
R3104C LEPTON CE DECLARATION OF CONFORMITY CAEN RFID Srl Via Vetraia, 11 55049 Viareggio (LU) Italy Tel.: +39.0584.388.398 Fax: +39.0584.388.959 Mail: info@caenrfid.com Web site: www.caenrfid.com herewith declare under our own responsibility that the product: WR3104CXAAAA – Lepton x4 - 25dBm Reader Module corresponds in the submitted version to the following standards: ETSI EN 301 489-1 V2.2.3:2019...
Page 34
R3101C LEPTON UKCA DECLARATION OF CONFORMITY CAEN RFID Srl Via Vetraia, 11 55049 Viareggio (LU) Italy Tel.: +39.0584.388.398 Fax: +39.0584.388.959 Mail: info@caenrfid.com Web site: www.caenrfid.com herewith declare under our own responsibility that the product: WR3101CXAAAA – Lepton x1 - 25dBm Reader Module corresponds in the submitted version to the following standards: ETSI EN 301 489-1 V2.2.3:2019...
Page 35
R3104C LEPTON UKCA DECLARATION OF CONFORMITY CAEN RFID Srl Via Vetraia, 11 55049 Viareggio (LU) Italy Tel.: +39.0584.388.398 Fax: +39.0584.388.959 Mail: info@caenrfid.com Web site: www.caenrfid.com herewith declare under our own responsibility that the product: WR3104CXAAAA – Lepton x4 - 25dBm Reader Module corresponds in the submitted version to the following standards: ETSI EN 301 489-1 V2.2.3:2019...