Advertisement
IDC-100 |
USER MANUAL
SPECIFICATIONS
MODEL
INPUT VOLTAGE
NO.
RANGE (VDC)
IDC-100A-12
9 - 18
IDC-100B-12
20 - 35
IDC-100C-12
30 - 60
IDC-100D-12
60 - 120
IDC-100A-24
9 - 18
IDC-100B-24
20 - 35
IDC-100C-24
30 - 60
IDC-100D-24
60 - 120
NO LOAD CURRENT DRAW
INPUT TO OUTPUT ISOLATION
OUTPUT RIPPLE & NOISE
PEAK EFFICIENCY
COOLING
OPERATING TEMPERATURE
AND DE-RATING
HUMIDITY, NON-CONDENSING
PROTECTIONS
SAFETY AND EMC STANDARDS
eMissiONs
iMMuNiTy
AuTOMOTiVe DireCTiVe
INPUT / OUTPUT CONNECTIONS
DIMENSIONS (W x D x H)
WEIGHT
NOTe: specifications are subject to change without notice
TABLE 1.
exTerNAL iNPuT siDe Fuse & WiriNg
MODEL
FUSE SPECS
NAME
IDC-100A-12, 24
32 VDC, 15A
IDC-100B-12, 24, 48
58 VDC, 7.5A
IDC-100C-12, 24, 48
80 VDC, 5A
IDC-100D-12, 24
125 VDC, 2.5A
TABLE 2.
exTerNAL OuTPuT siDe Fuse & WiriNg
MODEL
FUSE SPECS
NAME
IDC-100A-12
32V, 10A
IDC-100B-12
32V, 10A
IDC-100C-12
32V, 10A
IDC-100D-12
32V, 10A
IDC-100A-24
32V, 4A
IDC-100B-24
32V, 4A
IDC-100C-24
32V, 4A
IDC-100D-24
32V, 4A
NOTES FOR TABLE 1 AND 2:
a) Wire sizes shown are based on 90oC / 194oF wire temperature rating and 2% voltage
drop over distance of up to 6' from battery or load for current = Amp rating of the fuse.
b) For distances > 6', use thicker wires to limit voltage drop to <2% for current =
Amp rating of the fuse.
TERMINATION OF CONNECTING WIRES:
c) Use 6.3mm / 1/4" "Quick Connect", Female mating terminal on the connecting
wiring. This type of terminal is available for maximum wire size of AWG #10.
MAX INPUT
OUTPUT
CURRENT (A)
VOLTAGE (VDC)
CURRENT (A)
<15
12.5
<7.5
12.5
<5
12.5
<2.5
12.5
<15
24.5
<7.5
24.5
<5
24.5
<2.5
24.5
< 25 mA
Yes. > 400V RMS
< 50 mV RMS
85%
By temperature controlled fan
-20 to +30oC / -4oF to 86oF
(De-rate linearly to zero at 70oC / 158oF)
Max 95%
Overload / short circuit on the output side;
Over voltage on the output side; Over voltage /
transients on the input side; Reverse polarity on
the input side; Over heating
EN55014-1
EN55014-2
UN Regulation ECE R10-4
Quick Connect ; Male, 6.3 mm /
1/4" flat blade
88.0 x 150.4 x 50 mm / 3.5 x 5.9 x 1.9 in
0.5 Kg / 1.2 lb
WIRE SIZE (Up to 6 Ft From Battery)
(SEE NOTE 1 BELOW)
AWG#12
AWG#18
AWG#22
AWG#28
WIRE SIZE (Up to 6 Ft From Battery)
(SEE NOTE 1 BELOW)
AWG#14
AWG#14
AWG#14
AWG#14
AWG#20
AWG#20
AWG#20
AWG#20
DIMENSIONS & LAYOUT
OUTPUT
8
5
8
8
8
4
4
4
4
5
LEGEND [For Figs. 2(a) and 2(b)]
1. Input + Terminal
2. Input – Terminal
3. Output – Terminal
4. Output + Terminal
5. Chassis Ground
6. Ventilation slots
When using wires thicker than AWG #10, you may terminate the wire as
follows:
• U se 6.3mm / 1/4" "Quick Connect" Female matting connector (AWG #10 size)
• U se around 2" piece of AWG #10 wire and crimp the connector to one
end Solder / splice the other end of AWG #10 wire to wire the thicker wire
Use of short length of 2" of smaller AWG #10 wire will not increase voltage
drop appreciably.
150.4
143.0
• Height: 50 mm
• Use 4 mm bolt for mounting
NOTE: All measurements are in mm
Not to scale
Fig 1. Dimensions (Bottom View)
1
2
3
4
Fig 2(a). Layout (Front View)
6
Fig 2(b). Layout (Back View)
• Quick Connect Male Terminals
• 6.3 mm / 0.25" flat blade
DC-DC Converter Manual
58
88
6
| 3
Advertisement
