Advertisement
Available languages
Available languages
INDOOR UNIT DISPLAY
1
1
2
1 TIMER (White)
2 OPERATION (White)
● Display brightness can be adjusted, follow procedure on !.
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the Installation Manual).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type) following the (+)
and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
AIR FLOW DIRECTION
3
1
Press
: Move the louver in
the desired vertical direction.
Press
: Swing the air
2
automatically and press again to
stop.
For horizontal direction, adjust
3
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
REMOTE CONTROL
4
1 Infrared signal emitter
2 Start/Stop button(
)
3 Mode select button (
4 Temperature button (
5 Fan speed button (
)
6 Swing louver button (
)
7 Set louver button (
)
8 Off timer button (
)
9 High power button (
)
0 Economy button (
)
! Clear button ( )
@ Check button (
)
AUTOMATIC OPERATION
5
To automatically select cooling or fan only operation
1. Press
: Select Auto A.
2. Press
: Set the desired temperature. Min: 17°C, Max: 30°C
3. Press
: Select AUTO, LOW , LOW+
MED+
, or HIGH
1144180209-00_S01_182x257_12p_S_p70_211118.indd 4
1
)
)
3
2
7
9
8
@
, MED
,
.
COOLING / FAN ONLY OPERATION
6
1. Press
: Select Cool
2. Press
: Set the desired temperature. Min: 17°C, Max: 30°C
Fan Only: No temperature indication
3. Press
: Select AUTO, LOW , LOW+
MED+
, or HIGH
DRY OPERATION
7
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
: Select Dry
2. Press
: Set the desired temperature. Min: 17°C, Max: 30°C
Note: Dry mode fan speed is set to Auto only.
Hi POWER OPERATION
8
To automatically control room temperature and airflow for faster cooling
(except in DRY and FAN ONLY mode)
Press
: Start and stop the operation.
ECO OPERATION
9
To automatically control room temperature to save energy (except in DRY and
FAN ONLY mode)
Press
: Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
TIMER OPERATION
10
Set the timer when the air conditioner is operating.
Setting the OFF timer
1
Press
for enter OFF timer setting.
2
Press
for select desired OFF timer. (0.5 - 12 hrs)
3
Press
for set OFF timer.
4
Press
again for cancel OFF timer.
DISPLAY LAMP BRIGHTNESS ADJUSTMENT
11
To decrease the display lamp brightness or turn it off.
1. Press and hold
4
or
) is shown on remote control LCD then release the button.
6
2. Press
or
Rise
5
Decrease
0
!
Remote control
LCD
Lamp illuminates full brightness.
Lamp illuminates 50% brightness.
Lamp illuminates 50% brightness and the operation lamp
is turned off.
All lamps are turned off.
● In the examples of
and
going off.
or Fan only
.
, MED
,
.
.
for 3 seconds until brightness level (
,
to adjust brightness in 4 levels
Operation display
Brightness
100%
50%
50%
All turned off
, the lamp illuminates for 5 seconds before
22/12/2564 8:22:55
,
Advertisement
