Summary of Contents for Hi-Tech All-U-Need GLASS/CRYSTAL
- Page 1 ES T . 1984 ES T . 1984 HI TECH HI TECH All-U-Need GLASS/CRYSTAL MODEL INSTRUCTION MANUAL...
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS IMPORTANT! READ FIRST For your own safety be sure to read, understand and follow all warnings, safety rules and instructions in this instruction manual before using this machine. Failure to do so can result in serious personal injury. This instruction manual is intended for the following machine models: 20-027, 21-017, 20-026 and 21-007. - Page 3 SAFETY INSTRUCTIONS • Always wear proper eye protection to protect • Do not allow water to run down the shaft you from any debris that may fly out while and into the motor. This will cause the motor to grinding. We recommend wearing safety goggles instantly burn out.
-
Page 4: Table Of Contents
ACCESSORIES FAQS TROUBLESHOOTING REGISTER YOUR PRODUCT Scan the QR code below to register your product. Registering your Hi-Tech Diamond All-U-Need is essential to facilitate any warranty related requests. You can also register your machine hitechdiamond.com/register or over the phone with us at (630) 596-9909. - Page 5 (630) 596-9909. Important note: You have registering your All-U-Need to receive our up to 45 days from the purchase date of this Hi-Tech warranty service. Diamond machine to add this extended warranty.
-
Page 6: Machine Details
MACHINE DETAILS The image below shows parts and accessories included with your All-U-Need machine: Water cup with black water tube and valve Silver arbor with black knob and washer Black spray shield All-U-Need base unit (1/4 hp variable speed motor) Clear drain tube Water cup with cup holder 3/32"... -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Knob and Carefully unpack the All-U-Need from the box washers and remove all loose foam and accessories. Set the packaging aside should you need it in the future. Check to make sure all parts are present on both the machine and in the accessory kit. If Arbor you find any missing or damaged parts, call us immediately at 1 (630) 596-9909 or email us at... -
Page 8: Grinding And Polishing
GRINDING AND POLISHING STEP 1: ROUGHING The 360# diamond disc is the coarsest disc that comes with this All-U-Need. If you have less than a millimeter to remove, we suggest skipping this step and begin at step 2. The 360# disc is required if you need to remove a large amount of material from your work piece, or to remove glass left from the punty. - Page 9 GRINDING AND POLISHING remove. You must return to step 1 (360# disc) and start this process over. If after this step, your piece has a finely frosted finish, then you are ready to move onto step 4. STEP 4: PRE-POLISHING The 3,000# diamond disc removes the satin-like finish from the previous step.
-
Page 10: Maintenance
MAINTENANCE OILING CLEANING The only part you need to oil on the All-U-Need The All-U-Need is designed to be easily disas- machine is the inside of the 2" silver arbor. This is sembled for cleaning. Aft er each use, rinse the required because the motor shaft and arbor are black splash guard and flush out the white catch made of diff erent materials. -
Page 11: Cooling System
COOLING SYSTEM INSTALLING THE PRO-FLOW ATTACHMENT This feature is not available on all models. Attach your Pro-Flow water cooling system to any side of the All-U-Need white catch tray. Tighten the thumbscrews to fasten. Connect the Pro-Flow clear tubing to the water pump or pressure tank. -
Page 12: Accessories
ACCESSORIES For more Hi-Tech Diamond products and accessories, visit hitechdiamond.com. Backing plates Tech-11 polishing pads Our 6" and 8" acrylic backing plates provide a Our 6" and 8" Tech-11 polishing pads are made flat surface to back diamond discs and polishing with a thick felt and serve as a general polishing pads. - Page 13 ACCESSORIES For more Hi-Tech Diamond products and accessories, visit hitechdiamond.com. Electroplated diamond discs Electroplated diamond laps Our 6" and 8" diamond discs are used for precise Our 6" and 8" diamond laps use high quality rough and fine grinding on glass and stone.
-
Page 14: Faqs
FAQS What lubricants should I use with the Do you sell electrical spare parts for All-U-Need? my All-U-Need? Whom do I contact if I need a repair or replacement for my We recommend using only clean water with All-U-Need? the All-U-Need. If desired, you may add a water soluble coolant to the water. -
Page 15: Troubleshooting
What should I do if the drain tube on page 10. If it impossible to remove, please keeps clogging with sediment? contact Hi-Tech Diamond at 1 (630) 596-9909 and If the drain tube keeps clogging with leftover rock one of our specialized technicians will help you sediment, simply flush out the sediment with lots over the phone for correct removal. - Page 16 EST. 1984 ES T . 1984 HI TECH HI TECH MANUFACTURED BY Reentel International Inc. 44 Plaza Drive Westmont, IL 60559 - USA PHONE 1 (630) 596-9909 EMAIL sales@hitechdiamond.com WEBSITE hitechdiamond.com FACEBOOK facebook.com/hitechdiamond YOUTUBE youtube.com/hitechdiamond INSTAGRAM instagram.com/hitechdiamond Rev 05/18/23...