Table of Contents
Advertisement
Quick Links
DOL 192 12-20 Egg Counter
Technical User Guide
English For other language variants of this document we refer to:
Español Para otras variantes del idioma de este documento, visite:
Français Pour les versions dans d'autres langues de ce document veuillez consulter:
http://docs.skov.com/1091
604314 • 2018-06-19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Skov DOL 192 12
Summary of Contents for Skov DOL 192 12
- Page 1 DOL 192 12-20 Egg Counter Technical User Guide English For other language variants of this document we refer to: Español Para otras variantes del idioma de este documento, visite: Français Pour les versions dans d'autres langues de ce document veuillez consulter: http://docs.skov.com/1091...
- Page 2 Should any mistakes or imprecise information occur in spite of this, SKOV A/S would appreciate being notified thereof. • Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage caused or alleged to be caused by reliance on any information contained herein.
-
Page 3: Table Of Contents
4.4.2 DOL 192 20.......................... 15 Circuit Diagram .......................... 16 4.5.1 DOL 192 12.......................... 16 4.5.2 DOL 192 20.......................... 16 5 Maintenance Instructions .......................... 17 Cleaning............................. 17 Recycling/Disposal........................ 17 6 Technical data............................... 18 DOL 192 12 - 20 cm........................ 18 Technical User Guide... -
Page 4: Product Description
AC egg counters), so that it fits the conveyor belt. • DOL 192 12 cm scan width 120 mm, 24 V DC is suitable for counting eggs on longitudinal conveyor belts. • DOL 192 20 cm scan width 120 – 200 mm, 24 V DC is suitable for counting eggs on longitudinal conveyor belts. -
Page 5: Product Survey
The DOL 192 12 cm Egg Counter is suitable for counting eggs on longitud- inal conveyor belts. The DOL 192 12 cm Egg Counter must be powered using a 24 V DC ex- ternal power supply (135752). 130331 DOL 192 20 cm wo/display w/fitting Scan width 120 –... - Page 6 DOL 192 12-20 Egg Counter 136471 DOL Ext. box Small 20RL Extension box with two I/O module, 10RL 8AI 8AO, type 15 Includes rubber sleeves and ribbon cable 20 x relays 16 x 0-10V inputs 16 x 0-10V outputs Technical User Guide...
-
Page 7: Mounting Guide
DOL 192 12-20 Egg Counter 3 Mounting guide 3.1 Recommended Tools A list of tools recommended for the installation of your egg counter can be seen below. Topic Description Cordless drill Screwdriver bits Drill kit Utility knife Multimeter Tape measure... -
Page 8: Mounting Of Brackets
Remember angle of the egg control bracket; see illustration below. Mount the screw and wing nut on the middle of the bracket. Angle of egg control bracket Mount the DOL 192 12 on the bracket and tighten the wing nut. Technical User Guide... -
Page 9: Dol 192 20
DOL 192 12-20 Egg Counter 3.2.2 DOL 192 20 Mount the egg counter legs using 4 screws, 4 washers and 4 nuts, as shown in the illustration. Mount the screw and wing nut on the middle of the bracket. Mounting angle of egg control bracket Mount the DOL 192 20 on the bracket and tighten the wing nut. -
Page 10: Mounting On Conveyor Belt
(sun) light, or ensure that it is protected from sources of light. In the event of too much light, the red LED will turn on. (DOL 192 12-20) In the event of too much light, warning # 4 (DOL 192 30-75) will appear on the display. -
Page 11: Dol 192 20
DOL 192 12-20 Egg Counter 3.3.2 DOL 192 20 Flat conveyor belt Mount the bracket so that there is approx. 62 mm between the upper side of the conveyor belt and the bottom of DOL 192 20. The distance between the top of the egg and the egg counter should be approx. -
Page 12: Adjusting The Scan Width
DOL 192 12-20 Egg Counter 3.3.2.1 Adjusting the scan width If the scan width of DOL 192 20 cm is wider than the width of the conveyor belt, some of the infra-red sensors should be turned off. Set the dipswitch on scan module 2 (slave), see table be- low. -
Page 13: Installation Guide
DOL 192 12-20 Egg Counter 4 Installation Guide When the power supply to the egg counter is turned on, the egg counter runs a self-test for 2 seconds. It is sub- sequently ready to count eggs. The green and red LED’s on the front will light up (= orange) during the self-test. -
Page 14: Cable Plan
DOL 192 12-20 Egg Counter Or select 1 egg per pulse for all egg counters in the menu Technical | Setup | Adjustment | Production | Eggs | One input for egg per pulse all egg counters The DOL 539/535’s installation menu shows precisely which terminals the egg counter should be connected to. -
Page 15: Connection In The Egg Counter
DOL 192 12-20 Egg Counter 4.4 Connection in the egg counter The switch is closed in standby mode = conveyor belt OFF 4.4.1 DOL 192 12 4.4.2 DOL 192 20 Technical User Guide... -
Page 16: Circuit Diagram
DOL 192 12-20 Egg Counter 4.5 Circuit Diagram The egg counter is powered by an external 24 VDC power supply. 4.5.1 DOL 192 12 Example of terminal number For correct connection see the setup menu Show Installation on controller NOTE! Only if Pull up is displayed in ‘Show connections’... -
Page 17: Maintenance Instructions
DOL 192 12-20 Egg Counter 5 Maintenance Instructions 5.1 Cleaning The egg counter is maintenance-free but should be kept free of litter and dirt. Clean the product with a cloth that has been wrung out almost dry in water and avoid using: •... -
Page 18: Technical Data
DOL 192 12-20 Egg Counter 6 Technical data 6.1 DOL 192 12 - 20 cm DOL 192 12 DOL 192 20 Electrical V DC 8 - 30 Operating voltage Max. power Standby input kΩ Input impedance Standby level Pulse output 1 egg per... - Page 20 SKOV A/S • Hedelund 4 • Glyngøre • DK-7870 Roslev Tel. +45 72 17 55 55 • www.skov.com • E-mail: skov@skov.dk...
Need help?
Do you have a question about the DOL 192 12 and is the answer not in the manual?
Questions and answers