Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Powermat PM-SSZ-600
Summary of Contents for Powermat PM-SSZ-600
- Page 1 USER MANUAL Outboard engine PM-SSZ-600...
-
Page 2: Table Of Contents
Table of Contents SYMBOLS WARNING / INFORMATION ..................3 APPLICATION EQUIPMENT ......................... 3 TECHNICAL DATA ..........................4 SAFETY ........................... 4 GENERAL THOUGHTS ............................4 PREPARATION ..........................6 INSTALLATION AND OPERATION ......................6 Mounting the engine .......... -
Page 3: Symbols Warning / Information
Class II insulation APPLICATION EQUIPMENT Outboard engine POWERMAT is intended for consumer use in boats and pontoons designed for up to four people. It is not intended for professional work, lucrative. Any other use than described in this manual is the improper use of the device. For resulting from misuse or changes in the design of equipment damage or injuries responsibility of the user / operator and not the manufacturer. -
Page 4: Technical Data
TECHNICAL DATA Model PM-SSZ-600 engine type 4-stroke, one cylinder Number of cylinders Capacity 196 cm 196 cm maximum speed 7000rpm Idle 3000rpm 4,9kW / 6,5 maximum power Fuel gasoline 95 Fuel tank oil tank 0.6 l 2.08 postponement Forward / neutral racing Max. - Page 5 f) Make sure that all passengers on board are wearing life jackets. f) Make sure that all passengers on board are wearing life jackets. g) When loading a boat, make sure that the weight is evenly distributed. g) When loading a boat, make sure that the weight is evenly distributed. h) Follow the terms of executing the inspection h) Follow the terms of executing the inspection and) Do not make any alterations or modifications to the engine or its components.
-
Page 6: Preparation
PREPARATION and) To open the packaging and remove the device. and) To open the packaging and remove the device. b) Remove the protective film and the transport protection (if any). b) Remove the protective film and the transport protection (if any). c) Check whether the package parts are removed and keys. -
Page 7: Starting A Cold Engine
Starting a cold engine ATTENTION! The default engine is not flooded with oil. Before commissioning pour motor oil. Then you should regularly check the oil level. and) Loosen the bleed screw on the fuel tank by turning it 2-3 full turns. and) Loosen the bleed screw on the fuel tank by turning it 2-3 full turns. -
Page 8: Cleaning The Fuel Tank
Cleaning the fuel tank Remove the cover of the fuel filter, empty fuel tank, the fuel filter pull out and remove the water, mud and other debris by rinsing tank chemicals. Fuel tank cleaning should be done once every six months. Maintenance of the fuel filter Download the spark plug, fuel tank Delay. - Page 9 • Rest it on any metal part of the engine to the ground, but away from the fuel tank. • Rotate the engine. Observing the spark plug electrodes can be seen if there is a spark between them once every full rotation of the crankshaft.
-
Page 10: Replacing The Oil In The Gearbox Screw
e) Check that the spark plug washer is in good condition and replace the candle by hand to prevent e) Check that the spark plug washer is in good condition and replace the candle by hand to prevent turning the thread. f) After the initial manual screwing the spark plug wrench to tighten the spark to carefully push f) After the initial manual screwing the spark plug wrench to tighten the spark to carefully push washer .If installing new spark plug, tighten after screwing it manually key 1/2 turn to compress the washer. -
Page 11: Storage
Even minor damage to the screws can cause a decrease in speed. In case the propeller is bent, chipped or cracked, replace it with a new one recommended by the manufacturer. Every three months, you should download and lubricate the screw shaft. Storage Before the start of storage, you should empty the fuel tank and thoroughly clean the engine. - Page 12 Install the bracket 27 as shown in the figure. Prior to assembly, loosen the screw 37, the bracket 27 and the bolt 38 together with the mount shaft 41. Then mount 4 of the gasket 42 as illustrated, and the screws 37. Ensure that the whole assembly no backlash.
-
Page 13: Periodic Maintenance
Periodic maintenance It should be guided by the table below for maintenance outboard and extend its life. In the case of intensive use and, if necessary, these activities should be done more frequently. 3 months 6 months One month 1 year Rinse engine pure water... -
Page 14: Company Information
COMPANY DETAILS PH Powermat TMK Bijak Sp. General Partnership Ul. Defenders of the Gdansk Post 97 42-400 Zawiercie... -
Page 15: Scheme
SCHEME DEVICE Lp. part Name Lp. part Name 3 screw with a plain washer number 1 propeller 4 oil seal 5 a gear housing Two mounting screw... -
Page 16: Declaration Of Conformity
6 bearing 26 frame 26 frame 7 output axis 27 bracket 27 bracket 8 pin axis 28 supporting frame 28 supporting frame 9 a large gear 29 cover 29 cover thirty switch thirty switch 10 bearing 10 bearing 11 flange bearings 11 flange bearings 32 the handle assembly 32 the handle assembly...
Need help?
Do you have a question about the PM-SSZ-600 and is the answer not in the manual?
Questions and answers